







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
KraftMaid Windows & Doors: The Boulder City Owner’s Guide
KraftMaid is a cabinetry brand, not a window and door manufacturer, so what Boulder City homeowners actually call us about is the window-and-door side of a KraftMaid kitchen or bath remodel: new glazing that has to match the cabinet door profile, drawer-front detailing, and the finish schedule already written into the project. Installed window replacement in Boulder City runs $4,500 – $15,000, and impact-rated units run $8,000 – $25,000; door and glazing swaps tied to a KraftMaid layout are quoted as part of the written scope before work starts. We install to KraftMaid specifications using documented brand product, and we are an independent service provider, not affiliated with KraftMaid.
Owners usually figure out something’s wrong in one of two ways. Either the window or door unit was specified alongside the cabinetry and the finish, sightline, or rough opening doesn’t match what the KraftMaid drawings call for, or an existing unit next to the new cabinets has started fogging, sticking, or leaking and now has to be resolved inside a project that’s already in motion.
Key Takeaways
- KraftMaid doesn’t make windows or doors. Matching glazing to a KraftMaid layout is a specification job, and it’s where most of the cost risk sits.
- Installed window replacement in Boulder City: $4,500 – $15,000. Impact window installation: $8,000 – $25,000.
- We write the price before work starts. The number doesn’t move at the door.
- Every completed project carries the 365-Day Done Right Promise: if the work fails inside a full year, we come back and correct it at no charge.
Which KraftMaid Models This Applies To

KraftMaid cabinetry lines – including the Maple, Oak, and Cherry species across their door styles, plus the finish systems they’re ordered in – each carry a door profile, a drawer-front detail, and a finish code. Those are what set the visual rules for the window and door trim, the glazing grid, and the casing in the same room. When we scope a Boulder City project, we start with the KraftMaid order confirmation and the cabinet door sample, not with a tape measure and a guess.
Identifying the correct unit for a KraftMaid-matched room comes down to three items. First, the rough opening: width, height, and depth, measured inside the framed opening rather than across the old trim, because trim covers the gap that matters. Second, the finish code on the KraftMaid spec sheet, which determines whether the window or door unit gets a stained, painted, or factory-finished surround. Third, the door style name, so the casing profile lines up with the cabinet door edge instead of fighting it.
The OEM-versus-aftermarket call works differently here than it does with cabinets. Because KraftMaid is not the window manufacturer, there is no “KraftMaid window part” to source – there’s a KraftMaid specification to meet, and the unit itself comes from a window and door maker. What we do is match the glazing, frame, and finish to that KraftMaid spec and document it in the written scope. That keeps the specification traceable and takes the guesswork out of which unit actually belongs in the room.
One compatibility gotcha worth naming: a KraftMaid insert or shelf-pull-out in a base cabinet near a window can constrain the rough opening more than a homeowner expects. A right-hinged unit that clears the cabinet door in the showroom will hit the pull-out every time you open it. We check swing clearance against the KraftMaid layout before ordering anything.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your KraftMaid Windows & Doors Is Failing
- Fogging or condensation between the panes. That’s a failed seal in the insulated glass unit, not a cleaning problem. Once the seal goes, moisture works into the cavity and the unit will not clear.
- Sticking, dragging, or hard-latching operation. Usually a shifted frame or worn hardware rather than a bad unit. In Boulder City’s dry heat, wood frames and casings move through the season, and a hinge or rollers that were fine in spring can bind by August.
- Water staining on the interior casing or drywall around the opening. Often a failed perimeter seal or flashing detail at the exterior, which lets wind-driven rain past the frame. This one gets worse quietly until the substrate behind the trim is soft.
- Daylight visible around the frame, or a draft you can feel at the edges. Air infiltration, usually from a compressed or broken weatherstrip or a frame that’s out of square. In Boulder City’s summer heat, that draft is money leaking out of the house.
- Finish failure – peeling, flaking, or fading on a stained or painted surround. Sun exposure on a south or west elevation does this first, and it often shows up before the unit itself fails. Catch it early and it’s a refinish; catch it late and it’s a replacement.
A hard truth about lifespan in this climate: a decent vinyl or fiberglass window unit is typically rated for 20 to 25 years, but the exterior seal and finish on a wood-framed unit can fail years earlier under Boulder City’s sun and dry-air cycle. That gap is why we check the seal and finish on every opening, not just the ones the homeowner flagged.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included

Here’s what Boulder City homeowners actually pay, installed, not shop-quoted:
| Scope | Installed Price Range |
|---|---|
| Window replacement (standard units) | $4,500 – $15,000 |
| Impact window installation | $8,000 – $25,000 |
| Door unit swap tied to a KraftMaid layout | Quoted in the written scope with the project |
The range is driven by three things: how many openings, the unit’s glass package and frame material, and how much surrounding trim and casing has to be rebuilt to match the KraftMaid finish schedule. A straight unit swap in one opening sits at the low end. A whole elevation of impact-rated units with new casing and interior trim to match KraftMaid cabinetry sits at the high end, and $8,000 – $25,000 is where that lands.
Every price we give is a written line-item price before work starts. Parts, labor, trim, and disposal are broken out, so you can see where the money goes instead of taking a lump sum on faith. The 365-Day Done Right Promise applies to the completed work: if it fails within the full year, we return and correct it at no charge.
DIY or Call Us?
Some of this an owner can check safely. Look for fogging between the panes, run your hand around the interior frame for a draft, open and close the unit a few times to see if it binds, and check the exterior sealant line for cracks or gaps. Measure the rough opening inside the framing so you know what you’re working with. None of that puts you at risk.
Where DIY goes wrong: replacing an insulated glass unit, re-flashing an opening, and swapping a whole window or exterior door unit. Window and door work on upper floors involves height and heavy glass, and a bad flashing detail you can’t see from inside is the thing that rots the wall six months later. If the unit serves an exterior door, the safety and security of the opening depend on getting the hinge and latch set right, and a poor install is a real problem for your home. We can’t recommend taking that on.
We background-check and uniform everyone who comes to your door, and a live person answers the phone around the clock. For a straight answer on what your KraftMaid-matched opening actually needs, call (844) 797-9259.
FAQs

Twenty to twenty-five years is typical for a quality vinyl or fiberglass unit, but the exterior seal and finish on a wood-framed unit can fail years earlier under Boulder City’s sun and dry-air swing. That’s why we inspect seals and finishes on every opening during a project, not just the ones you flagged.
Sometimes, yes. A failed weatherstrip, a hinge or roller, a latch set, or the exterior sealant line can often be repaired or reset without a full unit swap. Fogging between the panes and a frame that’s gone out of square are replacement jobs, because the insulated glass unit and the frame itself are the failure. We’d rather tell you a repair is the right call than sell you a window you don’t need.
A single standard window unit swap is typically a one-day job once the unit is on site. A whole elevation, or impact-rated units with new casing and interior trim to match KraftMaid cabinetry, takes longer, and we put that timeline in the written scope before work starts. We don’t quote a date we can’t stand behind.
Since KraftMaid doesn’t manufacture windows or doors, the unit itself comes from a window and door maker and the KraftMaid side is the specification to meet: door profile, finish code, and casing detail. We work against that KraftMaid spec, document which unit we’re installing and why, and keep the manufacturer’s specs and warranty on file alongside our own guarantee. That’s traceable in writing, not carried in someone’s head.
Bradford Remodeling also installs and services Cambria, Silestone, and Kohler products when a KraftMaid project calls for them, and The Garrison Standard puts every price and guarantee in writing before a single tool comes out.
Call Bradford Remodeling Boulder City at (844) 797-9259 for a free estimate. We put the price in writing before any work starts, stand behind the finish with the 365-Day Done Right Promise, and leave the site clean with the signed guarantee in your hand. We are an independent service provider and not affiliated with KraftMaid.
Written by the team at Bradford Remodeling Boulder City, serving Boulder City and nearby areas.












