







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Silestone Home Additions & ADU: The Boulder City Owner’s Guide
We build Silestone-spec additions and ADUs (accessory dwelling units) in Boulder City, and the typical installed price for an addition runs $45,000 – $130,000, while a full ADU runs $90,000 – $220,000. These are planned builds, not same-day work – a real schedule, permits pulled, inspections passed. Most owners discover a problem with their Silestone surfaces and units in the same way: a hairline crack spreading across a countertop edge in the ADU kitchenette, or a sealant bead pulling away at the base of a new wet wall where the addition meets the original house. By the time they call, the small issue has usually been growing for a season.
Key Takeaways
- Additions run $45,000 – $130,000; full ADUs run $90,000 – $220,000 in Boulder City.
- Silestone engineered quartz is not repairable like natural stone – cracks and chip-outs often mean replacement of the panel, not a patch.
- We give you a written price before any work starts, and every project carries the 365-Day Done Right Promise.
- Boulder City’s heat and hard water are genuinely hard on sealants and substrate – we spec for both.
Which Silestone Models This Applies To

Silestone is Cosentino’s engineered quartz line, and it’s used across a wide range of series – from the classic Nebula and River series to the newer Ethereal, Le Chic, and Loft collections. What matters for an addition or ADU isn’t the series name on its own; it’s the slab thickness and edge profile your original install specified. Standard Silestone slabs are 2 cm or 3 cm thick, and if you’re matching a countertop into an addition, matching the original thickness keeps the sightline clean where the new room meets the old. The model name on the installation paperwork usually appears on a fabricator’s tag or a Cosentino warranty card, and if you can’t find either, a photo of the slab edge next to a tape measure is enough for us to identify it.
Here’s the OEM-vs-aftermarket decision specific to Silestone: Silestone doesn’t sell replacement slabs to homeowners directly, so the “OEM part” is the genuine Cosentino slab from an authorized distributor, and the “aftermarket equivalent” is a compatible engineered quartz from another producer. We recommend the genuine slab when you’re matching an existing Silestone surface, because color batches shift slightly between production runs. We’ll source it and quote it in writing. We are an independent service provider, not affiliated with Silestone or Cosentino.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your Silestone Home Additions & ADU Is Failing
- Hairline cracks along an inside corner. Quartz is rigid, and a corner cantilevered without proper substrate support flexes under load until it cracks. This shows up first in ADU kitchenettes where the counter spans a short cabinet run.
- Chip-outs at the sink or cooktop cutout. Those are stress points where the slab is thinnest. A dull blade during the original fabrication leaves micro-fractures that open up under thermal cycling.
- Sealant pulling away at the wall or wet-wall junction. In Boulder City’s dry heat, sealant beads shrink and lose adhesion faster than in cooler, wetter climates. It’s not a Silestone failure – it’s a maintenance item most owners don’t know to check.
- Discoloration or dullness in a sun-facing surface. Engineered quartz holds color well, but prolonged direct sun through an unshaded ADU window can fade the finish over years. A UV-blocking film on that window solves it.
- Water staining or lifting near the base of a new wet wall. This usually points to substrate moisture from the addition’s plumbing rough-in, not the quartz itself. It needs to be traced before any surface is replaced.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
Replacing a damaged Silestone counter in an addition or ADU runs $2,000 – $6,500 installed, depending on the length of the run, whether there’s a sink or cooktop cutout, and whether you need to match an existing color batch. A full countertop installation across a new ADU kitchen is $2,000 – $6,500, and an island adds $3,000 – $10,000 if it’s part of the scope. The range driver is slab size and cut complexity – a straight run with no cutouts sits at the low end; an L-shaped counter with a sink cutout and a matched edge profile sits higher. Parts and labor are both itemized in the written quote before we start. The 365-Day Done Right Promise covers the installation work for a full year: if the counter or the sealant fails within that window, we come back and correct it at no charge.
DIY or Call Us?
An owner can safely check a few things before calling. Look at the sealant bead where the counter meets the wall and the backsplash; if it’s cracked or pulling away, that’s a maintenance item you can flag. Check under the counter for staining on the cabinet finish, which points to a moisture problem worth tracing. What you shouldn’t do is try to remove or reset a Silestone slab yourself. Quartz is heavy, rigid, and unforgiving – a 3 cm slab can weigh well over a hundred pounds, and a dropped or improperly braced slab cracks clean through. It also needs to be cut with a wet saw for a clean edge, which is not a homeowner tool. If you’re seeing a crack, a chip, or a sealant problem, call (844) 797-9259 and we’ll take a look and give you a written price.
FAQs

Silestone engineered quartz typically holds up for 15 – 25 years in normal use, and in Boulder City’s climate the surface itself holds up well. The sealant and substrate are what need attention sooner – plan to check the sealant every few years, especially on sun-facing surfaces and around wet walls.
Small chips at an edge can sometimes be filled and color-matched, but a crack that runs through the slab usually can’t be repaired reliably – engineered quartz is rigid, and a repaired crack tends to reopen under load or thermal movement. We’ll tell you honestly which situation you’re in before you commit to anything.
A straightforward counter replacement in an addition or ADU is typically a one-to-two-day job once the slab is on site. The slab itself has to be ordered and fabricated to your measurements, which usually adds one to three weeks depending on the color and thickness.
We source genuine Cosentino Silestone through authorized distributors and quote the slab, fabrication, and install as line items in your written price. If you’re matching an existing surface, we’ll confirm the color and thickness against your original paperwork or a measured photo before we order. We don’t carry stock or keep parts on a truck – every slab is ordered to your job and documented.
Call (844) 797-9259 for a free estimate on your Silestone addition or ADU work in Boulder City. You’ll get a written price before any work starts, and a real person answers the phone around the clock.
Written by the team at Bradford Remodeling Boulder City, serving Boulder City and nearby areas.












