







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Moen Bathroom Remodeling: The Boulder City Owner’s Guide
We handle Moen bathroom remodeling in Boulder City, and the work runs $9,000 – $28,000 for a full bathroom, with smaller scopes landing in the $5,000 – $12,000 range. Most owners don’t call us because they want a remodel. They call because something failed first, and the failure usually shows up as a slow drip at the shower valve handle, a tub spout that won’t hold a stream, or water staining the drywall behind the surround. When a Moen cartridge, valve trim, or rough-in component gives out, the repair often turns into a scope decision, and that decision is where we come in.
Which Moen Models This Applies To

Moen builds a wide catalog, and the part that fits one series will not fit another. The two most common families in Boulder City bathrooms are the single-handle Posi-Temp shower valves (found in most homes built from the mid-1990s forward) and the older two-handle Chateau and Legend trim lines. If you’re identifying a part, look for a model number stamped on the valve body behind the trim plate, not on the handle cover, which is often a decorative cap with no useful numbers.
For Moen specifically, the OEM-versus-aftermarket call matters. Aftermarket cartridges for a Posi-Temp 1222 or 1225 valve run a few dollars, but the tolerances on the brass stem and the seating surface are where the cheaper units drift. If you’re keeping the valve body, use the OEM cartridge. If the valve body is pitted or the trim is twenty years old, replacing the whole rough-in and trim set is often the smarter spend, and that’s usually a bathroom remodel conversation, not a repair.
The series difference is where most Boulder City owners get stuck: a 1222 and a 1225 cartridge are visually similar but not interchangeable, and a Moen 1200 valve from an older home takes a different cartridge entirely. Check the stamp before you buy.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your Moen Bathroom Remodeling Is Failing
- A drip at the shower handle when the valve is off. The cartridge’s internal seals have worn, and water passes the ceramic disc even in the closed position. Left alone, this drip erodes the valve seat and turns a cartridge swap into a valve replacement.
- Temperature drift or a handle that won’t hit full hot. On a Posi-Temp valve, the pressure-balancing spool inside the cartridge has stiffened, which is common after years of hard water. The handle moves, but the water does not follow it.
- Water staining on the drywall behind the shower surround. A failed seal at the valve body or the tub spout threads lets water track behind the tile. By the time you see the stain, the substrate is usually wet and the repair scope has widened.
- A tub spout that won’t hold a stream, or a shower diverter that leaks past. The diverter seat and the spout’s internal O-ring wear out, and water runs out of the spout while you’re trying to shower. This is a fifteen-minute part swap if the threads are intact.
- Water pooling at the base of the toilet or vanity. A failed Moen supply stop or angle valve under the sink is the usual cause, and it’s the one failure on this list most likely to have already damaged flooring in a Boulder City bathroom.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included

Here’s what the work runs in Boulder City, installed:
| Bathroom remodel, full scope | $9,000 – $28,000 |
| Small bathroom remodel | $5,000 – $12,000 |
| Shower replacement | $3,000 – $8,500 |
| Tub-to-shower conversion | $3,500 – $10,000 |
| Walk-in shower installation | $4,500 – $12,000 |
| Bathroom vanity installation | $800 – $3,000 |
What moves the number: whether the valve body gets replaced or just the cartridge, whether the substrate behind the surround is wet, and whether you’re keeping the existing layout. A cartridge-only repair sits near the bottom of these ranges. A valve-and-trim replacement with new substrate pushes toward the middle. We put the price in writing before any work starts, with the line items broken out, and the 365-Day Done Right Promise covers the completed work for a full year. If it fails inside that window, we come back and correct it at no charge.
DIY or Call Us?
Changing a Moen cartridge is a task a careful homeowner can do, and we’ll tell you that plainly. Shut the water off at the main, not just the fixture stop, pull the retainer clip, and use the plastic cartridge puller Moen sells for the job. The tool matters. Forcing a stuck cartridge with pliers is how valve bodies get scored, and a scored valve body means replacing the whole rough-in behind the wall. That’s the point where the job stops being a DIY repair.
Anything behind the wall, any work where the substrate is wet, and anything involving the supply lines to a toilet or vanity is where we’d rather be the ones with liability on the job. Call (844) 797-9259 and a live person picks up, day or night, and we’ll give you a written price before anything starts.
FAQs

Expect roughly 8 to 12 years for a Moen brass cartridge in Southern Nevada’s water. Boulder City’s water carries dissolved minerals from the Colorado River supply, and those minerals gradually stiffen the pressure-balancing spool and wear the ceramic seat. If your cartridge is past the ten-year mark and the handle has started feeling gritty, plan on a replacement rather than waiting for a drip.
Sometimes, yes. A Moen cartridge can be cleaned and re-greased with silicone plumber’s grease if the seals are intact, which buys a year or two. But a cartridge that has already dripped in the closed position is usually past cleaning, and a pitted valve seat can’t be repaired at all. We’ll tell you which one you’re looking at before we quote the job.
A cartridge replacement usually takes about an hour from water shutoff to water back on. A valve body and trim replacement, which means opening the wall behind the shower, typically runs a half day to a full day depending on how the substrate comes out. Call (844) 797-9259 for an exact quote on your bathroom, and estimates are free.
We buy OEM Moen components through the manufacturer’s distribution network, matched to the valve model number stamped on your valve body. We don’t stock parts on a truck, so we confirm the exact model and order before the crew arrives. We also install KraftMaid, Cambria, and Silestone in the same bathrooms, all held to manufacturer specs and warranty terms that back our own written guarantee.
Bradford Remodeling Boulder City is an independently owned and operated member of the Garrison Partners family, held to The Garrison Standard, and we’re not affiliated with Moen. Our technicians are background-checked and uniformed, and every job closes with a clean site, a documented scope, and your signed written guarantee in hand. If a Moen fixture failed in your Boulder City bathroom and you’re weighing repair against remodel, call (844) 797-9259 for a free estimate.
Written by the team at Bradford Remodeling Boulder City, serving Boulder City and nearby areas.












