







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
American Standard Kitchen Remodeling: The Boulder City Owner’s Guide
We install American Standard kitchen remodeling in Boulder City, and full kitchen projects here typically run $14,000 to $45,000 installed, with smaller scopes landing between $9,000 and $20,000. Planned remodels aren’t same-day work; we schedule them, put the price in writing, and finish them in sequence. When your American Standard fixture or hardware fails, you usually find out the same way everyone does: a cabinet hinge sags and won’t hold adjustment, a drawer glide grinds halfway out, or a caulk line at the sink base pulls away and water gets behind it. This guide tells you what to check, what a replacement costs in Boulder City, and where a part swap ends and a remodel begins.
One clarification up front: Bradford Remodeling Boulder City is an independent remodeling contractor, not affiliated with American Standard. We install and replace American Standard-compatible components and document every model and part number we specify.
Which American Standard Models This Applies To

American Standard’s kitchen presence breaks into three groups, and each takes different replacement hardware. Their kitchen faucets and side-spray assemblies use proprietary cartridge and aerator threads, so a generic big-box cartridge won’t seat. Their stainless and composite sinks carry specific cutout templates and drain hole sizes, which matters when a new sink has to drop into an existing countertop opening. And American Standard-branded cabinet hardware and drawer systems follow their own mounting patterns for hinge cups and glide spacing.
To identify what you actually have:
- Faucets: check under the sink. The model number is stamped on the shank or on a tag near the supply lines, not on the spout where most people look.
- Sinks: measure the cutout, the basin depth, and the drain diameter. A quarter inch of mismatch will cost you a countertop cutout.
- Cabinet hardware: measure hinge cup bore (American Standard uses standard 35mm in most lines, but verify) and glide rail spacing before ordering.
On the OEM-versus-aftermarket question: for faucet cartridges, OEM is worth it. Aftermarket cartridges for American Standard faucets frequently have slightly different O-ring durometer and start weeping within a year in Boulder City’s hard water. For cabinet hinges and glides, a quality aftermarket equivalent from a documented brand is fine and often better built than the original. We specify through our standing brand roster, including KraftMaid, Cambria, and Silestone for cabinet and surface work, so every part is traceable to a manufacturer spec.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your American Standard Kitchen Remodeling Is Failing
- Faucet dripping at the spout or base. The cartridge seals have worn or mineral scale has scored the ceramic disc. Boulder City’s water runs hard, and we see cartridge failures here at 4 to 6 years rather than the 8 to 10 many homeowners expect.
- Cabinet doors that drift out of alignment. The hinge plate screws are pulling from the cabinet substrate, usually because the panel is particleboard and has swollen from a past leak. Tightening won’t hold; the substrate has to be addressed.
- Drawers that stick or won’t close flush. Glide rails have bent, or the rear mounting bracket has stripped. On American Standard soft-close glides, the damper is usually the first thing to go.
- Caulk or grout failing at the sink and backsplash. Movement between countertop and wall, or water intrusion behind the backsplash. Catch this early or the cabinet box below starts to delaminate.
- Loose sink clips or a sink that rocks. Undermount clips have corroded, or the adhesive bond has let go. A rocking sink stresses the countertop cutout and can crack a stone edge.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included

Here’s what kitchen work runs in Boulder City, installed, with the price written down before we start:
| Scope | Installed range |
|---|---|
| Full kitchen remodel | $14,000 – $45,000 |
| Small kitchen remodel | $9,000 – $20,000 |
| Cabinet installation | $4,000 – $13,000 |
| Countertop installation | $2,000 – $6,500 |
| Backsplash installation | $800 – $2,500 |
| Kitchen island installation | $3,000 – $10,000 |
What drives the range: cabinet grade and box count, whether the countertop needs a new template or can be reused, and whether we’re opening a wall or moving a rough-in. A single faucet cartridge swap sits at the low end; a full cabinet and counter replacement sits at the top. Every price is quoted line by line, parts and labor separated, and the number you sign is the number you pay. All completed work carries the 365-Day Done Right Promise: if it fails within a year, we come back and correct it at no charge.
DIY or Call Us?
Some things are safe to check yourself: visual inspection of caulk lines, measuring a cutout, confirming a model number from the tag under the sink, and tightening a cabinet hinge screw to see whether it holds. That’s diagnosis, not repair.
Where DIY goes wrong: cartridge replacement on a live supply line, undermount sink re-clipping (a dropped cast-iron sink ruins a countertop and can injure a foot), and anything that requires cutting a countertop or cabinet box. There’s also an electrical caution here. If your American Standard kitchen includes a disposal, dishwasher, or under-cabinet lighting tied into the same circuit, shut the breaker before you touch anything behind the cabinet, and call a licensed electrician for wiring. We don’t hand out instructions that put a homeowner in front of live current.
If the part is failing and you want it matched, priced, and installed correctly the first time, call (844) 797-9259 for a free estimate. A live person answers, day or night.
FAQs

How long does an American Standard kitchen faucet or cartridge last in Boulder City?
Expect 4 to 6 years on a cartridge here, shorter than the national average because of hard water and the intense sun that bakes anything near a window. Call (844) 797-9259 and we’ll price a replacement cartridge and check the supply lines at the same time.
Can the part be repaired instead of replaced?
Sometimes. A dripping faucet is often just a cartridge and seat, a cheap fix. But a cabinet box that’s swelled from water damage can’t be repaired, only replaced, and a countertop with a failed undermount cutout usually needs a new template. We’ll tell you which side you’re on before you commit to anything.
How long does the swap take?
A faucet or cartridge replacement is usually a single visit of an hour or two. Cabinet hardware or a sink replacement takes most of a day. A full kitchen remodel is scheduled over weeks, not done in a day, and we give you a written start and finish window up front. Call (844) 797-9259 to schedule your free estimate.
How do you source the American Standard part?
We match the model number from your fixture to the correct replacement, source from a documented supplier, and specify through our standing brand roster so the part is traceable. You get the part number and the price on the written quote before any work starts. Estimates are free at (844) 797-9259.
Written by the team at Bradford Remodeling Boulder City, serving Boulder City and nearby areas.












