







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Toto Home Additions & ADU: The Boulder City Owner’s Guide
We build Toto-spec home additions and ADUs in Boulder City, and a complete addition typically runs $45,000 – $130,000 while a detached ADU runs $90,000 – $220,000. Those are installed numbers, quoted in writing before work starts. When owners call us about a “Toto part,” what’s usually failed is the fixture package inside the build – the Toto shower valve, the fill valve in a Toto toilet, the thermostatic cartridge in a Toto shower – and the leak or temperature swing shows up months after the addition was signed off.
Which Toto Models This Applies To

Toto’s residential lineup splits into clear families, and each one uses different parts. The Drake, Ultramax, and EcoPromenade toilets run fill valves and flappers that don’t swap between the two-piece and one-piece bodies. The Toto shower valve bodies (the Thermostatic Mixing Valve and the pressure-balance series) take cartridges shaped for that specific valve model, not the trim you see on the wall. The trim plate and handle are cosmetic; the cartridge behind it is what fails.
To identify the right part, look for the label stamped inside the toilet tank lid or on the valve body behind the trim plate. Write down the full model string, not just “Toto.” Then measure: fill-valve shanks differ by a few millimeters, and a cartridge that’s close isn’t compatible.
On OEM versus aftermarket: for Toto specifically, we install OEM parts on anything behind a wall or inside a valve body. Aftermarket fill valves and flappers are reliable and cost less; aftermarket cartridges for a thermostatic valve are where we’ve seen early failures in Boulder City’s hard water. That’s the trade-off, and we’ll tell you which side of it each part sits on.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your Toto Home Additions & ADU Is Failing
- Water pooling at the base of a Toto toilet in the new bath. The wax seal or the fill-valve connection has let go, and it’s usually the shank nut loosening on a floor that settled after the addition was framed.
- Shower temperature swings you didn’t have before. The thermostatic cartridge is scaling up. Boulder City’s water runs hard, and hard water eats cartridges faster than the manufacturer’s spec sheet assumes.
- A toilet that runs for a few seconds after every flush. The flapper isn’t seating. On a two-piece Drake, that’s a $10 part; ignoring it adds real money to your water bill.
- Rust or mineral crust on the valve trim. The cartridge seal is weeping and drying against the trim. It looks cosmetic and isn’t – the leak is inside the wall.
- Reduced flow at one fixture only. A clogged aerator or a failing cartridge, not the whole system. Isolating it is the first diagnostic step.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included

Here’s what the work runs in Boulder City, parts and labor included:
| Item | Installed Range |
|---|---|
| Toto toilet fill valve / flapper (per fixture) | $120 – $280 |
| Toto shower valve cartridge replacement | $250 – $550 |
| Toto shower valve body replacement (behind wall) | $600 – $1,400 |
| Full Toto fixture package in a new addition bath | Part of the $45,000 – $130,000 addition |
What drives the range: whether the valve is behind a finished wall, whether the opening needs reopening, and whether the toilet is a one-piece or two-piece. Parts and labor are itemized separately. Every project carries our 365-Day Done Right Promise – if the work fails within a year, we come back and correct it at no charge.
DIY or Call Us?
A flapper, a fill valve, and a showerhead are genuine DIY work, and swapping a Toto flapper is ten minutes with a shutoff valve and a sponge. Anything inside a Toto shower valve body is not. Those cartridges sit behind a trim plate screwed to a rough-in that’s sealed to the wall, and forcing one out of a thermostatic body shears the internals. We’ve pulled too many half-removed cartridges out of walls in Boulder City to pretend otherwise. There’s also the water: shut it off at the fixture, not the main, and confirm the valve is closed before you touch anything. When you’re past your comfort line, call (844) 797-9259.
FAQs

How long does a Toto fill valve or cartridge last? A Toto fill valve typically lasts seven to ten years; a thermostatic cartridge in Boulder City’s hard water often runs five to seven. Flush a little less often and it lasts longer. Call (844) 797-9259 for an exact quote on yours – estimates are free.
Can it be repaired instead of replaced? Often yes. A Toto cartridge can sometimes be cleaned and reseated; a flapper can be adjusted. If the body itself is scored, replacement is the honest answer. We’ll tell you which it is before we touch anything.
How long does the swap take? A fill valve or flapper is 30 – 45 minutes. A cartridge is 45 – 90 minutes. A valve body behind a wall is a half-day. We quote the time in writing along with the price.
How do you source the part? We match the Toto model string to the OEM part number, then order from a supplier that documents the manufacturer’s spec. No open-box parts, no unlabeled equivalents. Materials carry manufacturer warranties that back our own 365-Day Done Right Promise. Bradford also works with KraftMaid, Cambria, and Silestone on the broader build.
To schedule a free estimate in Boulder City, call (844) 797-9259. We’ll match the part to your Toto model, quote a written price, and put the guarantee in your hand at close.
Written by the team at Bradford Remodeling Boulder City, serving Boulder City and nearby areas.












