







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Schluter Bathroom Remodeling: The Boulder City Owner’s Guide
Schluter bathroom remodeling in Boulder City runs $9,000 – $28,000 for a full bath and $5,000 – $12,000 for a small one, with a walk-in shower alone at $4,500 – $12,000. When a Schluter system fails, the homeowner almost never sees it first. They see the symptom: a grout line near the drain that keeps turning dark no matter how often it’s scrubbed, a hollow knock under a shower floor tile, or a waterproofing membrane that has let go at a corner and started to lift. By the time a loose tile or a soft spot shows up, the substrate behind it has usually been wet for months, not days. That gap between when it fails and when it shows is the whole reason we quote Schluter work with a written scope that names the membrane, the drain flange and the substrate – not just “tile the shower.”
Which Schluter Models This Applies To

Schluter’s bathroom work splits into a few product lines, and the part you need only fits the system it was made for. The bonded waterproofing membrane is KERDI, sold in rolls (commonly 3’3″ x 16’5″ and 3’3″ x 32’10”) and in pre-formed KERDI-BAND strips for seams and corners. The shower floor system is the KERDI-SHOWER line, and its drain assembly runs on the KERDI-DRAIN or the newer KERDI-LINE linear drain – the flange on these is sized to the drain body, so a replacement flange from the wrong series won’t seat. Uncoupling membrane is DITRA (the standard 1/8″ thick sheet) or DITRA-HEAT for radiant floor work, and the two are not interchangeable once the mat is bonded down.
Identify your part before you buy: read the print on the membrane edge (Schluter stamps the product name and roll size right on the fleece), check the drain body for its series marking, and measure the drain flange diameter, not the tile opening. The OEM-versus-aftermarket call matters here. Schluter’s own flanges and band are matched to the membrane’s fleece and its thin-set bonding spec; a generic membrane off a shelf may fit the same opening but won’t carry the same bonded-seam guarantee. We buy to the system, not to the opening size. Bradford Remodeling Boulder City is an independent service provider and is not affiliated with Schluter.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your Schluter Bathroom Remodeling Is Failing
- Tile that sounds hollow underfoot. A dull knock instead of a solid tap means the thin-set has separated from the membrane or the membrane from the substrate. In Boulder City’s dry heat, a floor that gets wet daily and dries hard can unbond faster at the edges than the middle.
- Grout that darkens and stays dark near the drain. That’s moisture trapped below the tile face, not on it. The membrane seam around the drain flange is the usual leak point because it’s where the most water moves and the hardest corner to band cleanly.
- Lifting or curling membrane at a shower corner. KERDI-BAND that wasn’t properly embedded in thin-set will peel at the inside corner. Once a corner lifts, water gets behind the membrane instead of staying in front of it.
- Efflorescence or white crust on grout and stone. Salt blooming out of the grout means water is moving through the assembly and evaporating at the surface. It’s the mineral signature of a slow leak, common on Boulder City’s harder water.
- A soft or spongy spot in the shower floor. The substrate itself is wet. By this point the repair is a tear-out, not a patch, because the framing and backer board behind the membrane are already compromised.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included

Installed pricing for the work that surrounds a Schluter repair depends on how far the failure spread. A full bathroom remodel in Boulder City runs $9,000 – $28,000; a small bathroom remodel, $5,000 – $12,000. Showers are the usual failure site, so the shower-only figures matter most: a walk-in shower installation is $4,500 – $12,000, a tub-to-shower conversion $3,500 – $10,000, and a straight shower replacement $3,000 – $8,500. A vanity swap, if the leak reached it, is $800 – $3,000.
What drives the range: whether the substrate is sound or has to come out, whether the drain is a center KERDI-DRAIN or a linear KERDI-LINE (linear drains cost more in both part and labor), and how much tile has to be matched or replaced. We quote parts and labor as separate line items so you see the membrane, drain and band cost apart from the install. Every completed project carries the 365-Day Done Right Promise – a written, full-year guarantee; if the work fails inside that window, we return and correct it at no charge. You get the written price before any work starts.
DIY or Call Us?
Some of this you can check safely. You can tap the floor for hollow spots, look for lifted membrane at corners, watch whether grout darkens after a shower, and read the product name stamped on the membrane edge so you know what you have. What goes wrong is the repair itself. Setting a KERDI drain flange or banding a shower corner correctly is a thin-set bonding job with almost no tolerance – the fleece has to embed fully or the seam fails again, often within a season. This isn’t spring-tension or live electrical work, so it won’t hurt you, but a bad bond means a second tear-out and a second bill. If the substrate is soft or the drain flange has let go, that’s the point to stop and call. Call (844) 797-9259 and we’ll walk the failure with you and give you a written price before anything starts.
FAQs

A properly installed Schluter shower assembly should hold 20 to 30 years, but Boulder City’s climate is hard on the failure points – dry heat and intense sun cure thin-set fast, which shortens the working window on a seam, and our harder water speeds up grout staining that masks a leak. The membrane itself outlasts the install if the seams were bonded right; most failures trace back to a seam or flange, not the membrane sheet.
Sometimes – a single lifted KERDI-BAND corner can often be cut back, re-banded and re-tiled without a full tear-out, if the substrate behind it is still dry and sound. Once the backer or framing is wet or soft, a patch just traps moisture and you’re back to a tear-out in a year. We’ll tell you which one you’re looking at before quoting. Call (844) 797-9259 for a free estimate.
A localized membrane and band repair with re-tiling runs a few days; a shower that needs the pan and drain redone is typically one to two weeks including cure time between thin-set and tile. We don’t quote a number we can’t hold, so the timeline comes with the written scope, not before it.
We buy to the system – the membrane, drain flange and band matched to the series you already have, sourced through suppliers who carry Schluter’s current product lines, so the part carries its manufacturer spec and warranty. We don’t claim to stock parts or carry them on a truck; we order what the job needs. We also work with KraftMaid, Cambria and Silestone where the remodel calls for cabinetry or surfaces.
Ready for a straight answer on your Schluter job? Call Bradford Remodeling Boulder City at (844) 797-9259 for a free estimate. A live person answers, day or night. You’ll get a written price before any work starts, background-checked technicians on the job, and the 365-Day Done Right Promise behind the finished work.
Written by the team at Bradford Remodeling Boulder City, serving Boulder City and nearby areas.












