







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Atlas Home Additions & ADU: The Boulder City Owner’s Guide
Bradford Remodeling Boulder City installs Atlas-compatible home additions and ADUs in Boulder City, and a typical project runs $45,000 – $130,000 depending on footprint, site conditions, and finish level. We are an independent service provider, not affiliated with Atlas. Owners usually come to us after the first-generation build-out starts showing its age: a sunroom that won’t hold a seal, an addition with a cold floor, or an ADU conversion where the original framing and tie-in were never squared up for Boulder City’s heat swings.
Which Atlas Models This Applies To

Atlas has produced several generations of panelized and site-assembled addition systems, and the part that fails differs by series. Before we price anything, we identify your shell by its data plate, usually stamped on the header or posted inside the rough opening, and confirm panel thickness, tie hardware spacing, and roof pitch.
The compatibility gotcha most Boulder City owners hit: older Atlas panel runs used 24-inch on-center framing that takes a different tie plate than the current 16-inch standard. Order the wrong plate and it will not seat, or worse, it seats without load transfer. That single mismatch trips more replacements than any finish-grade decision.
On OEM versus aftermarket: structural ties and anchors should come from a factory or a manufacturer that publishes load ratings to match your Atlas model. Finish components (trim, fascia, soffit) accept quality equivalents without issue. We source to spec and document what went in, so nothing is left to guesswork.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your Atlas Home Additions & ADU Is Failing
- A floor that flexes or feels soft near the perimeter. The sill or mudsill has taken moisture and the anchorage has loosened. In Boulder City’s dry heat, wood pulls back, and a loose anchor lets movement reach the floor.
- Daylight at the tie-in line. The panel-to-wall connection has separated. Thermal expansion across a Boulder City summer is what opens the gap.
- Ceiling fasteners popping or trim cracking. Load is shifting because a tie plate has backed out. This is a structural signal, not cosmetic.
- Interior moisture or condensation on walls in an ADU bath or kitchen. The addition’s rough-in venting was never sized for the added load. Look for swelling at the base.
- Roof sag or ponding at the eave of a flat addition roof. Deck deflection means the joist or header tie has softened. In Boulder City, these often show up after a monsoon dump that the original drainage couldn’t shed.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included

For Boulder City, a full home addition runs $45,000 – $130,000, an ADU construction runs $90,000 – $220,000, and a garage conversion runs $30,000 – $80,000. Where the part swap fits inside that range depends on three things: model generation (the 16-inch versus 24-inch framing difference above), the amount of hidden water or thermal damage found once the finish comes off, and whether roof and rough-ins need re-squaring.
Our scope is itemized on the written price before any work starts. You see the tie and anchor line, the framing line, the finish line, and the labor line as separate numbers. Nothing moves at the door.
Every completed job is covered by the 365-Day Done Right Promise: if the work fails inside a full year, we return and correct it at no charge.
DIY or Call Us?
You can safely check a few things: look for daylight at the tie-in, feel the floor for soft spots, photograph the data plate, and note any popped fasteners. Those observations help us quote accurately.
Where DIY goes wrong is structural. Tie plates, anchors, headers, and any work that carries load or opens a wall are not a homeowner job, and we’ll tell you so plainly. The wrong anchor in a Boulder City addition can fail under wind or seismic load in a way you won’t see until it does. Rough-ins and roof tie-ins belong to a trained professional, too.
Call (844) 797-9259 and a live person picks up, day or night. We’ll give you a written price before any work starts.
FAQs

How long does an Atlas addition or ADU last in Boulder City? A properly tied, correctly vented system should serve 20 to 30 years before a major part replacement. The variable in Boulder City is UV and heat cycling. Sun-exposed trim and sealants need attention sooner than they do in cooler climates.
Can it be repaired instead of replaced? Often yes. A loosened tie plate, a sealing gap at the tie-in, or a single failed anchor can usually be corrected without tearing out the addition. If the sill or header has structural damage, replacement is the honest answer. Call (844) 797-9259 for a determination.
How long does the swap take? A tie-plate or anchor repair is generally a one-day job. A larger framing or rough-in correction runs several days depending on scope. You get the timeline in writing with the price, not a verbal guess.
How do you source the part? We match the part to your Atlas data plate and source structural components to manufacturer specs. Finish components come from documented brands like KraftMaid, Cambria, and Silestone where finishes are involved, so specifications stay traceable. If a part is back-ordered, we tell you before we start.
Written by the team at Bradford Remodeling Boulder City, serving Boulder City and nearby areas.












