







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Tamko Bathroom Remodeling: The Boulder City Owner’s Guide
Tamko-compatible bathroom remodeling in Boulder City runs $9,000 to $28,000 installed, depending on the size of the room and how far the rebuild goes. We handle the full scope: tear-out, substrate, waterproofing, tile, fixtures, and finish – with a written price before any work begins. The same-range walk-in shower install sits at $4,500-$12,000; a straight tub-to-shower conversion runs $3,500-$10,000.
Owners usually arrive at this page the same way: a bathroom they thought was fine shows a soft spot in the floor, a grout line that keeps opening, or a shower pan that holds water where it shouldn’t. In Boulder City’s dry climate, the failure is rarely the surface. It’s underneath – a substrate that wasn’t sealed correctly, a pan that was set with the wrong setting bed, or a waterproofing membrane that was never continuous.
Which Tamko Models This Applies To

Tamko products show up in Boulder City bathrooms mainly in waterproofing membranes, shower pan liners, and roofing underlayment used above additions. If your home has a Tamko moisture barrier or membrane under the tile, the part number is usually printed on the exposed edge, or it’s listed in the original permit documents filed with the city. If you can’t find the label, we can identify it from a photo of the membrane edge and the thickness of the tile bed.
The OEM-vs-aftermarket decision matters here. Tamko’s membrane systems are spec’d as a complete assembly – membrane, sealant, and drain flange have to match. A generic membrane that’s “close enough” in thickness will pass the shelf test and fail the shower test. If we’re replacing a Tamko membrane, we match the assembly spec rather than substituting. Aftermarket equivalents are fine when the compatibilities line up; they’re not fine when the drain collar doesn’t seat to the same depth.
The same compatibility caution extends to surfaces and cabinetry when a bathroom remodel includes a vanity run: KraftMaid and Wellborn boxes measure differently at the wall, and Cambria and Silestone slabs are spec’d against the template, not a stock width. We check the whole assembly before the order goes in.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your Tamko Bathroom Remodeling Is Failing
- Grout lines that keep opening in the same place. The tile isn’t the problem. The substrate under it is moving, and a Tamko membrane that was installed over a wet or unsecured pan will telegraph that movement up through the finish.
- A shower pan that holds water after the drain dries. Water pooling at the flange usually means the membrane was lapped in the wrong direction or the setting bed was mixed too rich. It’s the failure we find most often in homes built before 2010.
- Soft spots in the floor near the toilet or shower curb. Water is getting past the surface and soaking the subfloor. By the time you feel it, the OSB or plywood underneath has usually been wet for months.
- Musty smell that doesn’t clear after cleaning. That’s not a cleaning problem. It’s moisture trapped in the wall cavity behind the tile, and it will keep cycling until the membrane and substrate are replaced.
- Loose tile with no visible crack. A tile that pops free without breaking almost always means the thinset released from the substrate. That’s a bond failure, and it spreads.
Nevada’s dry air hides these failures longer than a humid climate would. A wet pan in Phoenix shows mold in weeks; in Boulder City it can sit for a year and only show as a soft floor and a faint smell.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included

The $9,000-$28,000 range for a full bathroom remodel in Boulder City reflects three things: square footage, how much of the original substrate has to come out, and the finish level. A small bathroom remodel runs $5,000-$12,000. A walk-in shower installation is $4,500-$12,000; a tub-to-shower conversion $3,500-$10,000; a shower replacement $3,000-$8,500; a vanity installation $800-$3,000.
The written price covers tear-out, disposal, substrate repair, waterproofing, tile or surface finish, fixtures, trim, and cleanup. If the tear-out reveals rot the original quote couldn’t see, we stop, photograph it, and give you a written change before any additional work starts – not a number at the door.
| Scope | Installed Range |
|---|---|
| Full Bathroom Remodel | $9,000-$28,000 |
| Small Bathroom Remodel | $5,000-$12,000 |
| Walk-In Shower Installation | $4,500-$12,000 |
| Tub-to-Shower Conversion | $3,500-$10,000 |
| Shower Replacement | $3,000-$8,500 |
| Bathroom Vanity Installation | $800-$3,000 |
Every completed project is covered by the 365-Day Done Right Promise. If the work fails within that year, we come back and correct it at no charge – in writing, before the first tool comes out.
DIY or Call Us?
What you can safely check yourself: find the membrane label, photograph the pan edges, and confirm the drain holds. What you should not attempt yourself: pulling the shower pan, replacing a waterproofing membrane, or re-setting a flange. A membrane installed even slightly wrong looks fine for eight months and then takes the floor with it. Waterproofing is the one part of a bathroom remodel where the failure is invisible until it’s expensive.
We install to spec and stand behind it for a full year. That’s the whole point of the guarantee. Our technicians have up to 22 years of experience, and every job is background-checked and uniformed – you know who’s in your home before they arrive. Call (844) 797-9259 for a free estimate.
FAQs

A properly installed Tamko-compatible membrane assembly typically holds 15 to 25 years in this climate. The variable is installation, not the material – a continuous membrane on a sound substrate will outlast a hasty one by a decade.
Rarely. Spot repairs on a membrane almost always fail because the new material won’t bond to the old surface the same way. Replacing the pan is usually the only fix that holds, and it’s what we recommend when the failure is under the tile bed.
A shower replacement is typically 3 to 5 working days. A full bathroom remodel runs 2 to 4 weeks depending on scope. We give you the schedule in writing before work begins.
We match the membrane assembly to your existing system spec and order through the manufacturer’s documented supply channel – not a generic substitute. We’re an independent service provider, not affiliated with Tamko, but we install to their published specifications and back the work with our own written guarantee.
Call (844) 797-9259 for a free estimate. Bradford Remodeling Boulder City works with a documented roster of name-brand materials, including KraftMaid, Cambria, and Silestone, so the specification on your bathroom is traceable from order to close.
Written by the team at Bradford Remodeling Boulder City, serving Boulder City and nearby areas.












