







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Barrette Roofing: The Boulder City Owner’s Guide
We install Barrette-compatible roofing for Boulder City homeowners, and most repairs run $400 – $1,800 while a full replacement lands between $8,000 and $20,000 installed. We can usually get a crew out to look at a failure within a day or two of your call. Bradford Remodeling is an independent contractor and is not affiliated with Barrette.
Owners here tend to find the problem the same way. A summer windstorm rolls down off the McCullough Range foothills, and the next morning there are shingle tabs in the rock landscaping or granules piling up in the splash block against the wall. Sometimes it’s quieter than that: a brown ring on a ceiling in the back bedroom, or a fascia board that’s gone soft where you can reach it from a ladder. Barrette makes the trim and accessory side of roofing as much as the sheet goods, so when we say “the part,” we mean the specific piece – ridge cap, drip edge, valley flashing, vent, starter strip, or the panels themselves – and matching it to your model is the first thing we do.
Which Barrette Models This Applies To

Barrette’s roofing line covers more ground than most owners realize, and the part you need depends on which series was installed and when. The catalog spans metal panel profiles, composite shake and slate-look products, and the trim and flashing accessories that go with each. Two houses on the same street in Boulder City, built within a few years of each other, can have entirely different panel profiles because the builder switched suppliers between phases.
Here’s how we identify it. First, pull the original building permit file – Clark County keeps them, and a Boulder City permit record will usually name the product and the profile. Second, look for a stamp or label on the underside of a panel near the eave, which Barrette puts there on most of its lines. Third, measure: panel width, rib height, and exposure are the three numbers that tell us which series you’re on. Get those wrong and an aftermarket panel won’t seat or lock into the existing field.
On the OEM-versus-aftermarket question, the honest answer is that it depends on the part. Flashing and trim are usually fine to match from a quality aftermarket supplier if the profile and gauge are right, and that saves money. Panels and locking accessories are a different story – a mismatched rib profile will never seal, and trying to force it is how you end up replacing an entire slope instead of one section. For Barrette specifically, we lean OEM on anything that has to interlock and stay flexible on flat goods like drip edge and valley metal.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your Barrette Roofing Is Failing
Boulder City is hard on roofs in a specific way. We get brutal UV, wide day-night temperature swings, and wind that funnels through the Eldorado Valley with grit in it. That combination ages materials faster than the manufacturer’s desert-rating would suggest. The symptoms we see most often, and what’s actually causing each:
- Granule loss in the gutters or at downspout outlets. This is UV breakdown of the asphalt or coating binder. It’s the earliest sign a shingle or composite panel is past its useful life, and once it starts, patching doesn’t stop it.
- Lifted or curled panel edges along the ridge and hips. Thermal cycling causes the metal or composite to expand and contract daily, and the fasteners back out or the sealant fails. Wind then gets under the edge and peels it.
- Rust streaks or white oxidation on the drip edge and valley flashing. Our wind carries fine silica dust, which scratches coatings, and once the coating is gone the steel underneath starts to corrode. This is a $400 – $1,200 kind of repair if caught early.
- Water staining on ceiling or wallboard after a rain. This usually means flashing failure at a penetration or wall intersection, not a failed field panel. The leak shows up far from where it starts.
- Soft or delaminated fascia and soffit boards. Water is running behind the trim and soaking the substrate. We see this most on the south-facing eaves, which take the worst of the afternoon sun here.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included

Replacement costs in Boulder City break down the way you’d expect for parts plus labor, and the ranges below are what we quote:
- Roof repair (flashing, trim, localized panel work): $400 – $1,800
- Tile roof repair (tile and slate-look products): $600 – $2,500
- Full roof replacement: $8,000 – $20,000
- Metal roof installation (panel systems): $15,000 – $40,000
What drives the range is pitch and access, how much of the assembly is being replaced versus reused, whether the substrate is sound, and how many penetration flashings are involved. You get a written price before any work starts, itemized by part and by labor, so you can see exactly what a drip edge run costs versus a valley rebuild. Every repair we complete carries our 365-Day Done Right Promise: a full year in writing, and if the work fails inside that window, we come back and correct it at no charge.
DIY or Call Us?
There’s a safe side and an unsafe side here, and it splits cleanly at the roof edge. On the ground, you can and should check the gutters for granule buildup, look at the fascia from a stepladder, and photograph any ceiling stain so you know when it appeared. That’s useful information and it costs nothing.
What we don’t recommend is getting up on the roof yourself. It’s not just the height – it’s the surfaces. Barrette’s metal and composite products get slicker than asphalt when they’re dusty, and our desert grit makes every step a guess. Panel edges and metal trim are also sharp enough to open a hand. And the moment you’re up there working around the flashing and fasteners, one wrong pull can peel a panel seam that was holding fine. That’s how a $600 repair becomes a full slope. If you’ve got any of the symptoms above, call (844) 797-9259 and we’ll put eyes on it and give you a written price. It’s a free estimate.
FAQs

How long should Barrette roofing last in Boulder City? A properly installed system should hold up 20 to 40 years depending on the product line, but our UV and thermal swings push it toward the lower end of the manufacturer’s range. Metal panel systems tend to outlast composite and shingle-look products here because there’s no asphalt binder to break down. Call (844) 797-9259 for an exact quote on your specific product – estimates are free.
Can my failing Barrette roofing be repaired instead of replaced? Often, yes. Localized flashing, trim, or single-slope panel repairs are common and stay in the $400 – $2,500 range. Replacement only makes sense when granule loss is widespread or the panels themselves have lost integrity. We’ll tell you which one you’re looking at before any work starts.
How long does a Barrette part swap or repair take? A flashing or trim repair is usually a half-day to a full day. A partial panel replacement or a slope rebuild runs two to four days depending on access and how much substrate needs work. We schedule with a written scope so you know what day the crew arrives and what day they finish.
How do you source the right Barrette part for my roof? We identify your series from the permit record, the on-panel stamp, or physical measurements of rib height and exposure, then source the correct part. For interlocking components we use OEM; for flat goods like drip edge we match a quality equivalent when it saves you money without compromising the fit. Call (844) 797-9259 to get the identification started.
We also work with KraftMaid, Cambria, and Silestone on the interiors side for Boulder City homeowners who are renovating while the roof gets sorted.
If you’re in Boulder City and you’ve got a Barrette roof that’s showing its age, the next step is a written price, not a guess. Our technicians have up to 22 years of experience, we carry a full 365-Day Done Right Promise on completed work, and a live person answers the phone around the clock. Call (844) 797-9259 for a free estimate – you’ll get a real number in writing before any work begins.
Written by the team at Bradford Remodeling Boulder City, serving Boulder City and nearby areas.












