







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Unilock Bathroom Remodeling: The Boulder City Owner’s Guide
Unilock-compatible bathroom remodeling in Boulder City typically runs $9,000 – $28,000 installed, and we write that price down before we start, so it doesn’t move. Larger layouts with full walk-in showers, vanity replacements, and substrate work land at the high end; smaller rooms sit near $9,000. Most of these projects book as scheduled work rather than same-day callouts, because a bathroom is a sequence of tasks that has to dry and cure correctly between steps.
Homeowners in Boulder City usually find out something is wrong with the Unilock system before they know what to call it. Water pools at the shower threshold instead of draining. The floor paver joints wash out and refill with grey sand. A tile or paver edge pops loose after a winter cold snap. Sometimes the vanity top rocks because the wall behind it was never squared. These symptoms point at a handful of specific parts and details, and the fix is usually more precise than it is expensive.
Key Takeaways
- Installed range for a full Unilock bathroom remodel in Boulder City: $9,000 – $28,000.
- Most failures trace to substrate, drainage slope, or a single replacement part, not the whole system.
- We work Unilock and document every part and material call in writing before the first tool comes out.
- Every completed project carries the 365-Day Done Right Promise. If the work fails inside that year, we come back and correct it at no charge.
- Bradford Remodeling Boulder City is an independent service provider. We’re not affiliated with Unilock.
Which Unilock Models This Applies To

Unilock’s product line is organized by family, and the specific model matters because the substrate and jointing parts don’t interchange across families. If your home has a Unilock-branded shower or wet-area floor, the family name is usually stamped on a trim piece, an edge restraint, or a sample card left by the original installer. If there’s no stamp, we measure instead: paver thickness (common wet-area thicknesses are in the 1 1/2-inch to 2 3/8-inch range), joint width, and the drain or threshold profile.
The OEM-vs-aftermarket decision for Unilock is mostly about match, not preference. If the failing part is visible (a threshold, an edge piece, a jointing system), an OEM part keeps the look consistent and the fit exact. If it’s buried (a separation membrane, a drainage slope component), a quality engineered equivalent from a documented manufacturer works fine and often costs less, provided it meets the same spec. We tell you which side of that line each part falls on in writing, so you’re never guessing what you’re paying for.
Two things specific to Boulder City: (1) our local family set includes Unilock series with matching bathroom thresholds and compatible edge details, but the compatibility is not automatic across series. (2) Because Boulder City’s climate swings from triple-digit summers to occasional hard freezes, the jointing and setting materials matter as much as the visible part. A joint that survives a Colorado River summer may not survive a February frost if it’s spec’d for the wrong exposure.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your Unilock Bathroom Remodeling Is Failing
- Water pooling at the shower threshold or floor drain. The substrate slope was set flat or drained to the wrong point. Unilock systems drain by design, so if water sits, the slope or the drain assembly is the culprit.
- Jointing material washing out or turning soft. Sand-set or poly-set joints can degrade when the setting material was spec’d for a lighter trail, not a wet floor. We see this often in bathrooms where the floor doubles as a shower approach.
- Paver or tile edges lifting after a cold snap. Boulder City’s occasional freezes push moisture through the joint. If the edge piece was dry-set without proper adhesive or separation, it lets go when the water in the joint expands.
- Vanity counter rocking or gapping at the wall. The wall behind the vanity was never squared before the surface went in. This shows up as a visible gap or a counter that flexes under a hand.
- Grout or jointing darkening faster than the field. Dark, damp joints usually mean water is migrating under the surface. Left alone, this attacks the substrate and can force a partial tear-out.
Replacement Cost & What’s Included

Here’s how the numbers break down for Boulder City. These are installed prices, parts plus labor, and every one of them is written down before we start.
| Scope | Installed Range |
|---|---|
| Full bathroom remodel (Unilock-compatible) | $9,000 – $28,000 |
| Small bathroom remodel | $5,000 – $12,000 |
| Walk-in shower installation | $4,500 – $12,000 |
| Shower replacement | $3,000 – $8,500 |
| Bathroom vanity installation | $800 – $3,000 |
The range is driven by a few things: whether the substrate has to be rebuilt, how many parts are being swapped versus repaired, and the finish level you choose. A single threshold or edge piece replacement sits near the bottom of the shower-replacement range. A full shower rebuild with new drainage slope, substrate, and jointing lands higher. Labor is itemized so you can see what each part and each step costs. Every completed job is covered by the 365-Day Done Right Promise: if the work fails inside that year, we return and fix it at no charge.
We work a documented roster of brands beyond Unilock, including KraftMaid, Cambria, and Silestone, so surfaces and cabinetry match the rest of the room.
See the difference
Before
After
Before
After
Before
AfterDIY or Call Us?
Some checks are safe and worth doing yourself. You can measure your threshold width, photograph the model stamp or trim piece, and note where water pools after a shower. That information saves us time and helps us quote more accurately. You can also tighten a loose vanity anchor if the wall behind it is solid.
What you shouldn’t do yourself is rework the substrate slope, re-set a drainage assembly, or lift and re-bed a wet-area paver without knowing the exposure spec. Get the slope wrong and water migrates under the floor; get the jointing material wrong and the failure comes back in a season. Two of our technicians have up to 22 years of experience in this kind of wet-area work, and they’ll show you what failed and why before anything is replaced. Call (844) 797-9259 and a live person picks up, day or night. Estimates are free.
FAQs

A correctly installed Unilock wet-area system should hold its jointing and slope for 15 to 25 years in Boulder City conditions. The substrate and drainage slope are what determine lifespan, not the visible surface. If your system failed in under 10 years, the cause is almost always slope, setting material, or a specific part, and we’ll tell you which in writing.
Often, yes. A single failed edge piece, a threshold, or a jointing system can be repaired without touching the rest of the floor. Full replacement is only necessary when water has reached the substrate or the slope itself is wrong. We quote the repair first and only recommend the larger job if the smaller one won’t hold. Call (844) 797-9259 for a free assessment.
A single-part swap usually takes one to two days; a partial remodel runs three to seven days depending on cure time. We build the schedule into the written scope so there are no surprises about how long the bathroom is out of service. Large or full-remodel projects are quoted on a project schedule up front.
We identify the product family first, then confirm the spec by measuring and cross-referencing documented manufacturer data before ordering. That matters here because Unilock parts aren’t interchangeable across families, and the Boulder City climate means jointing and setting materials need to be spec’d for freeze exposure. You get the part description and cost in the written price before any work starts.
Get Your Free Written Estimate
If you’ve got a failing Unilock bathroom system in Boulder City, the next step is simple: call (844) 797-9259 for a free estimate. A live person answers 24/7. We’ll identify the part, give you a real number, and put it in writing before a single tool comes out. That’s The Garrison Standard, and it’s how we keep a bathroom project squared away from the first measurement to the signed guarantee in your hand.
Written by the team at Bradford Remodeling Boulder City, serving Boulder City and nearby areas.












