







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Dvele Kitchen Remodeling: The Boulder City Owner’s Guide
Dvele kitchen remodeling in Boulder City runs $14,000 to $45,000 installed, and that covers a partial refresh up through a full cabinet, countertop, and layout rebuild. We install Dvele-compatible cabinetry, panels, and finish components as part of that scope, priced in writing before any work starts. Most Boulder City owners don’t discover a failing Dvele component all at once. It starts with a cabinet door that won’t sit flush, a soft-close drawer that slams, or a panel seam opening near the sink, and the problem compounds through a full desert summer before anyone calls. That’s the moment this page is written for.
We’re an independent service provider. Bradford Remodeling Boulder City is not affiliated with Dvele, and we don’t claim to be.
Key Takeaways
- Dvele kitchen remodeling in Boulder City: $14,000 – $45,000 installed, written price before work begins.
- Dvele components are matched by model and series, not guessed – labels and measurements do the work.
- Boulder City’s low humidity and 100°F-plus summers are hard on cabinet boxes, adhesives, and hardware.
- Every finished project carries the 365-Day Done Right Promise: if it fails within a year, we return and correct it at no charge.
Which Dvele Models This Applies To

Dvele builds modular and panelized homes, so the kitchen components are specified per model line and per plan revision, not pulled from a universal catalog. Two Dvele homes that look identical from the street can carry different cabinet depths, different panel widths, and different hardware bore patterns depending on the build year and the plan revision stamped on the drawings. That’s the compatibility gotcha most owners run into: a replacement door or drawer front ordered by eyeballing the old one frequently arrives a few millimeters off, and a few millimeters is enough to throw the reveal out on the whole run.
Before we order anything, we identify the exact component three ways:
- Model and plan label. Look inside cabinet doors, on the back of drawer boxes, and on any panel edge near the sink base or pantry for a printed label or stamp with the model designation.
- Measured dimensions. Door and drawer front widths and heights down to the millimeter, plus the bore spacing on the hinge plate.
- Photo documentation. Cabinet interior, hinge type, panel joint, and the label itself, so the match is traceable rather than assumed.
On the OEM-versus-aftermarket decision for a Dvele kitchen: if the cabinet box is sound and only a door, drawer front, or piece of hardware has failed, a quality aftermarket match in the right species and finish is often the sensible, cost-effective route. If the failure is structural – a warped box, a failed panel joint, water damage at a sink base – patching around it costs more than it saves. We’ll tell you which one you’re looking at, with the reasoning, before you commit to either.
We also work alongside KraftMaid, Cambria, and Silestone when a Dvele kitchen is being updated beyond a straight component match.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your Dvele Kitchen Remodeling Is Failing
- Cabinet doors that won’t stay aligned. On a Dvele run, a door that drifts out of square usually points to a hinge plate working loose from the cabinet face, or to a soft-close hinge that’s lost tension. Both are repairable, but a repeated drift after adjustment means the plate hole is worn out, not the hinge.
- Drawers that slam or jump the track. The under-mount glide has either dropped off its rear clip or the drawer box has swelled at the bottom edge. Boulder City’s dry air pulls moisture out of a wood drawer box unevenly, and a box that’s shrunk past tolerance won’t run true no matter how many times you re-seat the glide.
- Panel seams opening near the sink or dishwasher. That’s moisture, not settling. A Dvele panel joint with an acrylic or PVA adhesive bead is a humidity-driven part, and once the bead lifts, water tracks into the substrate and the seam keeps opening after every repair.
- Soft-close hardware that’s gone slack or noisy. The damper mechanism has a finite cycle life – typically several thousand open-and-close cycles – and a drawer used ten times a day burns through that faster than anyone expects. Slack dampers are a hardware swap, not a cabinet replacement.
- Finish blistering or lifting on cabinet faces and panels. A finish that fails in one area first usually means the substrate saw moisture or the factory finish saw direct sun through a window. Both are common in south-facing Boulder City kitchens and both are correctable.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included

Every number below is an installed price for Boulder City – materials and labor together, not a bare-part quote with labor added later.
| Work scope | Installed price range (Boulder City) |
|---|---|
| Dvele-compatible kitchen remodel (full scope) | $14,000 – $45,000 |
| Small kitchen remodel | $9,000 – $20,000 |
| Cabinet installation / door and drawer front replacement | $4,000 – $13,000 |
| Countertop installation | $2,000 – $6,500 |
| Backsplash installation | $800 – $2,500 |
| Kitchen island installation | $3,000 – $10,000 |
What drives the range: whether the cabinet boxes survive or come out, the number of doors and drawer fronts matched, finish species and sheen match difficulty, and whether the scope stops at components or extends to counters, backsplash, and layout. We give you the number in writing before a single tool comes out, and it doesn’t move at the door. The finished work carries the 365-Day Done Right Promise – if a replacement door, drawer front, or panel fails within that year, we come back and correct it at no charge.
DIY or Call Us?
Replacing a soft-close hinge on a sound cabinet door is a reasonable DIY job with the right screwdriver and fifteen minutes. Adjusting a door that’s off by a millimeter after a hinge swap is where it usually goes wrong – the plate hole gets stripped, or the door twists and the whole run looks wrong. Replacing a cabinet door or drawer front by eye, without a measured match and bore spacing, is the single most common source of repeat work we see.
What you can safely check: hand-turn every hinge and glide, open and close each door and drawer slowly, and run your hand along panel seams at the sink base. What you should not attempt: re-glueing a panel joint that’s already taken water, or repairing a cabinet box that’s gone out of square – those need the panel removed and the substrate assessed, and a patch over a wet substrate will fail within the season.
Call (844) 797-9259 for a free estimate and a written price. A live person picks up, 24 hours a day, 7 days a week.
FAQs

Soft-close hardware typically holds up for roughly five to eight years of daily use, and cabinet doors and drawer fronts generally last longer unless the substrate gets moisture. Boulder City’s dry climate is hard on wood and easy on hardware, so the realistic failure pattern here is finish and panel-seam trouble before the box itself gives out. Call (844) 797-9259 for a free estimate on a replacement match.
Yes, often – a failing soft-close glide or hinge is a repair, and a sound cabinet box with a bad door front just needs the front swapped. Full replacement only makes sense when the box is warped, the substrate has taken water, or the panel joint won’t hold after a proper repair. We’ll give you both numbers in writing before you decide. Call (844) 797-9259 for a free estimate.
A door and drawer front swap is usually one day; a full cabinet and countertop scope runs several days to a couple of weeks depending on the size of the kitchen and whether counters are included. We give the schedule in writing alongside the price. Call (844) 797-9259 for a free estimate.
We measure the component to the millimeter – door width and height, drawer front dimensions, and hinge bore spacing – then photograph the interior, hinge type, and any surviving panel edge for documentation. That gives us a match we can trace back to your plan revision rather than a guess. Call (844) 797-9259 for a free estimate.
Bradford Remodeling Boulder City installs Dvele-compatible kitchen components and full kitchen remodels across Boulder City with a written price before work begins, background-checked and uniformed technicians on every job, and the 365-Day Done Right Promise on the finished work. Call (844) 797-9259 for a free estimate – a live person answers, day or night.
Written by the team at Bradford Remodeling Boulder City, serving Boulder City and nearby areas.












