







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Dvele Fence Installation: The Boulder City Owner’s Guide
We install Dvele-compatible fence systems in Boulder City for $3,500 – $9,000 installed, depending on run length, material, and gate count. Most projects are scheduled on a planned timeline, not a same-day emergency call: we survey the line, quote it in writing, then set an install date. Owners usually discover a failure the hard way. Posts start leaning after a windy spring, gate latches stop catching, or a panel sags between posts after a monsoon-bearing August. The fence is still standing, but it’s lost the structure it needs to hold a line or keep a dog in the yard.
Key takeaways
- Dvele fence systems are engineered as a kit – post spacing, rail dimensions, and fastener type are set by the manufacturer, not by whoever’s installing it.
- Boulder City sun and caliche soil both work against a fence installed without that spec in hand.
- Installed pricing here runs $3,500 – $9,000, quote in writing before work starts.
Which Dvele Models This Applies To

Dvele builds modular and panelized homes with an engineered fence package that matches the home’s site plan. The fence spec is tied to the model and elevation, not sold as a universal kit. That means the panel width, post spacing, and rail profile for a Dvele 700-series single-story run differently than for a two-story 1,200-series with a wider lot footprint. Two things identify the right part: the model plate on the home’s utility panel or electrical sub-panel, and the as-built site plan from your closing documents. Both give you the series and the fence package designation. If neither is handy, we measure the existing post-to-post spacing and rail profile on site – the panel width in inches is the fastest tell, and we’ve seen plenty of Dvele fences in Boulder City where a well-meaning prior owner mixed in a different rail gauge and threw the whole run off.
On the OEM-versus-aftermarket call, we’re honest about it. Dvele’s OEM fence components are matched to their engineering, and when the original posts and rails are intact, an OEM replacement panel or post keeps the line true. But for a Boulder City fence that’s lived through 10-plus years of sun, quality aftermarket equivalents in the same gauge and post size do the job – and often better, if the OEM spec uses a lighter picket than the desert UV and caliche ground warrant. We don’t keep any parts on hand or on a truck. We source to your model and spec, and the price you get reflects that.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your Dvele Fence Installation Is Failing
- Leaning posts after a wind event. Boulder City sits in a wind corridor with gusts that regularly push 40-plus mph. When a post is set shallow or the concrete footing is undersized, the first strong spring blows it out of plumb. By the time you see the lean, the footing has already moved.
- Gate sag and latch misalignment. A sagging gate usually means the post it hangs from has shifted or the hinge fasteners have pulled out of the wood. On a Dvele gate, the latch catches only at exact alignment, so a half-inch sag reads as a gate that won’t close.
- Rail separation between panels. When fasteners loosen or the rail shrinks after a dry summer, panels start to gap. That’s the climate doing its work – wood and composite both expand and contract hard in Boulder City’s swing between 100-plus-degree summers and cold desert nights.
- Soil heave at the post line. Boulder City’s caliche and expansive soils push footings up and out. A post that heaves a couple of inches over a winter pulls the panels out of alignment and opens gaps at the bottom rail.
- Splintering, checking, or fading pickets. A fence that’s five to seven years old in full Boulder City sun will show chalky finish and hairline checking on the picket faces. That’s normal surface wear, but it’s the cue that the finish and the fasteners need attention before the structure goes.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included

In Boulder City, a Dvele fence replacement runs $3,500 – $9,000 installed. That range covers removal of the failing run, post setting, and new panels with a single gate – the things that drive cost are total linear feet, post count and depth of the new footings, whether the route crosses caliche that has to be broken out, material choice, and the number of gates. A short standard run sits at the low end; a longer perimeter with a double gate and hard caliche sits at the high end.
We don’t quote a flat number and change it at the door. You get a written price before any work starts: parts, labor, and the disposal of the old fence as separate lines. Every install is covered by the 365-Day Done Right Promise – if the posts move or a panel fails within the guarantee period, we come back and correct it at no charge. That written guarantee goes in your hand at close, along with a clean site.
DIY or Call Us?
There’s honest room for a homeowner here, and we’ll tell you where it ends. What you can safely check: walk the line and eyeball plumb with a level against each post, wiggle a gate to feel the hinge play, and push on a bottom panel to see if a footer is loose. What goes wrong with DIY on this part is the footing. A Dvele fence wants a post depth and concrete volume that matches the model’s spec and the local soil, and caliche in Boulder City doesn’t give; homeowners who dig a shallow hole and set a post in bagged mix usually see it move within two seasons. If the failed post is carrying a gate, or the run has moved out of plumb, that’s the point to call. Give us the model plate details and we’ll source the right Dvele-compatible components, quote the line in writing, and set a date. Call (844) 797-9259.
FAQs

How long does a Dvele fence last in Boulder City? Ten to fifteen years is realistic here if the fence is installed to spec and the footings are sized for the soil. The posts and finish take the most punishment from Boulder City sun and wind; pickets and rails usually hold longer.
Can the failing section be repaired instead of fully replaced? Often yes. A single leaning post, a sagging gate, or a couple of checked pickets can be repaired without replacing the run, if the surrounding posts are still sound and the footing hasn’t moved. We’ll tell you straight which way the numbers fall. Call (844) 797-9259 for a written estimate.
How long does the swap take? A standard run with one gate usually takes two to four working days, plus any lead time on the Dvele-compatible panels and posts, since we source to your model rather than pull from stock. We put the schedule in writing with the price.
How do you source the Dvele part? We identify your model and fence package from the model plate and site plan, then source the panel, post, and rail to that spec – OEM where it’s available and quality aftermarket in the same gauge where it isn’t. No guessing, no part on the truck, and no substitute spec slipped in at the door.
If you’re also matching finishes inside the home, we work with KraftMaid, Cambria, and Silestone, among other documented brands.
Call Bradford Remodeling Boulder City at (844) 797-9259 for a free estimate on your Dvele fence installation. A live person answers the phone 24/7, every Boulder City quote is a written price before any work starts, and every completed install carries the 365-Day Done Right Promise. We’re an independent service provider and not affiliated with Dvele – which means we source to your model and your spec. Our technicians have up to 22 years of experience, and Boulder City homeowners get background-checked, uniformed technicians on every job.
Written by the team at Bradford Remodeling Boulder City, serving Boulder City and nearby areas.












