







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
American Standard Bathroom Remodeling: The Boulder City Owner’s Guide
We install American Standard bathroom fixtures and full bathroom remodels throughout Boulder City, with typical installed projects running $9,000 – $28,000 depending on scope, tile, and whether the layout moves. Most owners call us before a big number hits their desk: a toilet or shower component fails on a Friday, they drive to Henderson or order a part online, it doesn’t fit, and the small repair turns into a bigger question about an aging Boulder City bathroom. We give you a written price before any work starts, so you know the repair number and the remodel number side by side, in writing, with no figures that move at the door.
Which American Standard Models This Applies To

American Standard covers a wide field, and the part you need depends entirely on which line and production run you have. For toilets, the main branches are the Cadet, Champion, Colony, and Vormax families, each with its own fill valve, flush valve, and gasket set. A Champion 4 uses a different flapper and seal than a Cadet Pro, and a part pulled for one won’t seat properly in the other. For shower and tub work, the concern is the valve body and trim: American Standard’s lines have changed cartridge designs over the years, and a trim kit has to match the rough-in valve behind the wall, not just the handle you can see.
The fastest way to identify your model is the label. Toilets carry a stamp on the inside of the tank or behind the lid. Shower valves are labeled on the rough-in body, often visible only after the trim is off. If the label is gone, we measure: the tank bolt spacing, the spud size, the distance from the wall to the valve center. We work with OEM American Standard parts and quality aftermarket equivalents, and we’re clear about which is which. Aftermarket is often a real option for a fill valve or flapper; for valve cartridges and trim, OEM fit is usually the safer call. We also work with KraftMaid, Cambria, and Silestone when a bathroom remodel moves past the fixtures.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your American Standard Bathroom Remodeling Is Failing
- The toilet runs or refills on its own. The flapper or fill valve seal is worn and letting water past. In Boulder City’s dry air and hard water, that seal degrades faster than the manufacturer’s numbers suggest, and a slow leak can add real money to a water bill before you notice.
- A rocking toilet or water at the base. The wax ring has failed, or the flange is cracked. Water at the base rots the subfloor quietly, and by the time it shows, you’re looking at floor repair, not just a new ring.
- The shower handle drips or won’t shut off cleanly. The cartridge inside the valve body is worn. That’s the part behind the wall, and it’s the most common failure we see on older American Standard trim.
- Weak flush and repeated clogs. Mineral buildup in the jets and rim holes, common with local water, restricts flow. Sometimes it clears with a clean-out; sometimes the flush valve assembly is at the end of its service life.
- Cracked or crazed porcelain, or loose caulk at the wall. This points to movement and moisture behind the fixture. It’s the sign that a repair is becoming a remodel, and it’s worth pricing both before you commit.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included

Here’s what the numbers look like in Boulder City, installed, with parts and labor in one written figure rather than split into hidden line items:
| Project | Installed price range |
|---|---|
| Full bathroom remodel | $9,000 – $28,000 |
| Small bathroom remodel | $5,000 – $12,000 |
| Walk-in shower installation | $4,500 – $12,000 |
| Tub-to-shower conversion | $3,500 – $10,000 |
| Shower replacement | $3,000 – $8,500 |
| Bathroom vanity installation | $800 – $3,000 |
The range moves on tile choice, whether the rough-in stays put, and how much substrate work the floor or wall needs once we open it up. A single fixture swap sits at the low end; a full gut with new valve and tile lands at the top. Our technicians have up to 22 years of experience, and every completed job carries the 365-Day Done Right Promise: if the work fails within a full year, we come back and correct it at no charge.
DIY or Call Us?
Some things you can check safely yourself. Confirm the model from the tank label, wipe the fill valve and flapper clean, and see whether the water shuts off fully. Tighten a loose toilet bolt by hand, no wrench and no force, because over-tightening cracks porcelain. What we’d steer you away from is going behind the wall. Replacing a shower valve cartridge, swapping a valve body, or resetting a toilet flange in a tile floor means shutting off water, opening the wall or floor, and getting the seal right the first time. Done wrong, it leaks into the subfloor where you won’t see it for months. In Boulder City, where older homes often have tile set over older substrates, that risk compounds. Call us at (844) 797-9259 and we’ll price it straight.
FAQs

A flapper or fill valve typically lasts five to seven years; a shower cartridge runs longer but wears faster with hard water and heavy use. In Boulder City’s dry climate, seals dry out and crack faster than the manufacturer’s general estimates suggest. Call (844) 797-9259 for an exact quote, and estimates are free.
Often, yes. A running toilet or a dripping shower handle is usually a part swap, not a new fixture, and we’ll tell you honestly which one you’re looking at. If the porcelain is cracked or the flange is gone, though, replacement is the sounder money. We give you both numbers in writing so you can decide.
A toilet part swap or a flapper and fill valve set is a short visit, often under an hour. A shower cartridge replacement runs longer because the trim comes off and the valve has to be confirmed before it goes back together. A full remodel is measured in days or weeks, and we put the schedule in writing with the price.
We match the part to your exact model number from the label, then source either OEM American Standard or a quality equivalent we stand behind. We don’t guess from a photo, and we don’t carry parts on a truck; the right part is confirmed before we show up. Bradford Remodeling Boulder City is an independent service provider, not affiliated with American Standard.
When you’re ready to price it, call (844) 797-9259 for a free estimate. You’ll get a written price before any work starts, background-checked and uniformed technicians on the job, and a live person on the phone any hour of the day. Every project is backed by the 365-Day Done Right Promise, part of how we operate under The Garrison Standard as a member of the Garrison Partners family.
Written by the team at Bradford Remodeling Boulder City, serving Boulder City and nearby areas.












