







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Grohe Kitchen Remodeling: The Boulder City Owner’s Guide
Grohe kitchen remodeling in Boulder City is typically quoted at $14,000 – $45,000 for a full kitchen, and that range holds whether you’re keeping a Grohe pull-down faucet and matching Grohe accessories in place or specifying Grohe components into a new layout. We work with homeowners who already have Grohe fixtures in the kitchen and want them matched, replaced, or built around during the remodel. We’re an independent contractor and not affiliated with Grohe, so every spec gets measured and confirmed on site before we order anything.
The failures usually show up slowly. A Grohe pull-down sprayer that stops retracting, a faucet bonnet that drips at the base, a handheld handshower wand on a Grohe kitchen faucet that won’t hold the button. Boulder City sits above the valley with harder mineral content in the water than most of Clark County, and we see scale buildup eating seals and aerator screens faster here than down in Henderson or Las Vegas. Once a Grohe cartridge starts passing water or the pull-out hose loses pressure, homeowners notice it at the sink first and call after they’ve already been living with the drip for a few weeks.
- Full kitchen remodel: $14,000 – $45,000
- Small kitchen remodel: $9,000 – $20,000
- Cabinet installation: $4,000 – $13,000
- Countertop installation: $2,000 – $6,500
- Backsplash installation: $800 – $2,500
- Kitchen island installation: $3,000 – $10,000
Which Grohe Models This Applies To

Grohe kitchen products split into a few families and the part you need depends on which one you own. The two most common lines in Boulder City kitchens are the Grohe Eurosmart and Grohe Concetto single-handle pull-out faucets, plus the Grohe Minta and Grohe K7 semi-professional pull-downs in higher-end remodels. Each uses a different cartridge body and a different pull-out hose fitting. A Eurosmart cartridge will not seat in a Concetto valve body, and the hose ends are threaded differently between lines. That’s the compatibility gotcha that trips up a lot of online orders.
To identify your model, look under the sink deck plate or on the back of the faucet body for a small etched model number, or pull the base trim ring off and read the tag on the valve body. Measure the tailpiece spread and the spout reach so we can confirm. Grohe pushes its own cartridge line hard, and a genuine Grohe 46 374 000 style cartridge for a single-handle kitchen faucet runs in the $25 – $70 range depending on which body it fits. Aftermarket equivalents from ceramic-disc makers like Sedal and Kerox run $8 – $20 and fit certain Grohe bodies, but not all. On a Grohe you’re usually better staying OEM because the valve body seat tolerance is tighter than a generic cartridge is molded to. We source through plumbing supply distributors we can trace, not marketplaces with unverifiable origin. We also handle other brands on the same job, including KraftMaid cabinetry, Cambria and Silestone surfaces when the remodel goes wider than the faucet.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your Grohe Kitchen Remodeling Is Failing
- Drip at the spout when the handle is off. This is almost always a worn ceramic cartridge, not the O-rings and not the aerator. In Boulder City’s water, the ceramic disc faces score and start passing water within 5 – 8 years on a daily-use kitchen.
- Handle feels loose or grinds when you turn it. The retaining nut has backed off, or the cartridge stem has worn the handle broach. Tightening the nut buys time; a worn broach means a new cartridge and possibly a new handle.
- Pull-down sprayer won’t retract. The internal hose weight has slipped or the spring return inside the spray head is fatigued. On the Minta and K7 this is a serviceable head assembly, not a faucet replacement.
- Water pressure drops at the sprayer but is fine at the spout. Scale clogging the spray head screen or the diverter valve is stuck. Boulder City’s hard water builds mineral film on these screens in about 2 – 3 years of normal use.
- Water pooling at the base of the faucet on the counter. The base O-ring or the bonnet seal is failing. Left alone, water tracks under the deck plate and reaches the cabinet substrate, which is the point where a $20 seal becomes a $400 cabinet repair.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included

Fixing a failing Grohe component inside a kitchen remodel runs small: a cartridge swap or spray head replacement typically lands $120 – $280 installed when folded into a larger Boulder City job. If you’re remodeling the whole kitchen, the Grohe line item sits inside the $14,000 – $45,000 full remodel range and gets quoted separately on your written price sheet so you can see the number for the faucet, the number for the cabinetry, and the number for the counter. Small kitchen remodels run $9,000 – $20,000. What drives the range is cabinet grade, counter material, and whether the plumbing rough-in has to move for a new sink location.
Every price we give is written before a single tool comes out. No number moves at the door. Parts are quoted with brand and model so you can verify the spec. All completed work carries the 365-Day Done Right Promise: if the install fails inside a full year, we return and correct it at no charge. That covers the labor and the fitting, and it’s in writing in your hand at job close. Technicians who show up are background-checked and uniformed, and every one of them is listed on your scope before the crew arrives, so you know exactly who’s walking into your Boulder City kitchen.
DIY or Call Us?
You can safely do a few things yourself on a Grohe kitchen faucet. Turn off the supply stops under the sink, unscrew the aerator and clean the screen, check the pull-out hose weight and reposition it, and read the model tag on the valve body. Those are checks, not commits. The place most DIY goes wrong on a Grohe is cartridge extraction: the retaining clip on a Grohe single-handle body is small, hidden under the handle cap, and easy to lose down the drain, and if you force the cartridge out you can score the valve body seat. Once the seat is scored, the faucet body is done and you’re pricing a whole new faucet.
One thing to flag up front: any plumbing work that involves opening a supply line or working behind a cabinet under a live sink carries water damage risk if a fitting doesn’t seat. If you’re uncertain, stop and let a trained tech handle it. This isn’t a scare tactic, it’s the honest call. A real plumbing fitting torque is the wrong place to learn. Call (844) 797-9259 and we’ll schedule a free estimate, quote the part and the labor in writing, and if the fix is small we tell you that rather than selling a remodel you don’t need.
FAQs

Expect 5 – 8 years under normal daily kitchen use in Boulder City, shorter if you’re on hard water without a softener. Grohe ceramic cartridges are rated for hundreds of thousands of cycles in lab conditions, but real-world scale and mineral content at this elevation cut that lifespan significantly.
Yes, in most cases. A dripping spout, loose handle, or non-retracting sprayer is usually a cartridge or spray head swap, not a full faucet replacement. We diagnose on site and quote the repair first; if a scoring issue in the valve body means repair won’t hold, we tell you that straight and quote the replacement. Call (844) 797-9259 for a free estimate.
A cartridge or spray head replacement is typically a 30 – 60 minute job once the part is on hand. A full faucet replacement runs about 90 minutes to 2 hours, longer if the supply stops need replacing or the counter deck plate has to come off. We don’t promise same-day, but we don’t sit on parts orders either.
We order through manufacturer-authorized plumbing supply distributors where the model and origin are traceable, not marketplace resellers. You get the part brand, part number, and price on your written quote before we order it, and if a genuine Grohe part isn’t available in time, we tell you the lead time rather than substituting an unverified aftermarket equivalent.
Pull the base trim ring off the faucet, read the etched model tag on the valve body, and snap a photo. Have that ready when you call (844) 797-9259, and we can often confirm the exact cartridge before we’re on site in Boulder City.
If a Grohe fixture in your kitchen has started to drip, stick, or scale up, get it on the written scope now rather than waiting for the cabinet damage. Call (844) 797-9259 to schedule your free estimate. A live person answers, day or night, and you’ll have a written price in hand before any work starts.
Written by the team at Bradford Remodeling Boulder City, serving Boulder City and nearby areas.












