







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Mr-Glass Kitchen Remodeling: The Boulder City Owner’s Guide
Bradford Remodeling installs Mr-Glass-compatible kitchen remodeling in Boulder City, with most full kitchens landing between $14,000 and $45,000 depending on layout, cabinet line, and surface materials. Smaller jobs like a cabinet refresh or a countertop and backsplash swap run well under that range. We’re an independent service provider and not affiliated with Mr-Glass; we work with the brand’s products every week and we price the job in writing before anything is ordered.
Owners usually find the failure the same way. A cabinet door that used to close with a click now hangs a quarter-inch low, or the soft-close hinge gives a soft clunk and stops pulling the door shut. Maybe the drawer glide grinds near the end of its travel, or the finish on a Mr-Glass laminate front starts lifting along the bottom edge after a summer in a Boulder City kitchen that faces west. The rest of the kitchen is fine. One component is tired. That’s the moment this page is for.
Which Mr-Glass Models This Applies To

Mr-Glass has moved through several cabinet and component lines, and parts don’t cross freely between them. The two things that matter most when matching a replacement are the hinge bore pattern on the door (the two or three holes drilled into the back of the door face) and the drawer glide series, since a glide rated for a 75-pound drawer box won’t seat correctly in a cabinet built for a 100-pound box. Before you order anything, pull one door and measure the bore spacing center-to-center, then photograph the glide mounted to the cabinet side. The model label is usually on the inside of the sink base door or on the back panel of the cabinet box, not on the door face.
The OEM-versus-aftermarket call is real with Mr-Glass. Original hinges and glides match the factory bore exactly and drop in without redrilling; they cost more and sometimes carry a lead time. Quality aftermarket equivalents from established hardware makers are often a direct fit on the common bore patterns, hold up well, and cost less. On a Boulder City kitchen where the doors themselves are still solid, an aftermarket hinge with the right bore spec is a sensible choice. Where the cabinet box or door front carries the Mr-Glass finish you’re trying to preserve, stay with the OEM part so the color and grain stay consistent across the run. Our technicians have up to 22 years of experience reading exactly this difference.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your Mr-Glass Kitchen Remodeling Is Failing
- Doors that drift out of alignment. The hinge plate has loosened in the bore or the adjustment screw has backed out. Left alone, the door sags against the frame and starts rubbing finish off the edge.
- Soft-close that no longer catches. The damper inside the hinge has failed. It’s a wear item, and in a kitchen used twice a day it can give out years before the cabinet itself does.
- Drawers that grind or stick near the end of travel. The glide rollers have flat-spotted or the track has picked up grit. A failing glide puts side load on the drawer box, which is when the box itself starts to rack.
- Finish lifting along a bottom edge or near the sink. Moisture and desert heat cycling under a Mr-Glass laminate or thermofoil front will eventually loosen the bond. Boulder City’s dry summers and cold winter nights are hard on that bond line.
- Loose or stripped hinge screws. The screw holes in the cabinet frame have wallowed out from repeated load. This one gets worse fast, and it’s the failure most likely to drop a door.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included

Here’s what kitchen work in Boulder City runs, priced as installed ranges so you can plan against a real number:
| Scope | Installed range |
|---|---|
| Full kitchen remodel | $14,000 – $45,000 |
| Small kitchen remodel | $9,000 – $20,000 |
| Cabinet installation | $4,000 – $13,000 |
| Countertop installation | $2,000 – $6,500 |
| Backsplash installation | $800 – $2,500 |
| Kitchen island installation | $3,000 – $10,000 |
What moves a job inside that range: cabinet count and box size, whether the layout changes (which pulls in plumbing and electrical rough-in), surface material (Cambria and Caesarstone sit higher than a basic laminate), and whether we’re swapping components or replacing full cabinet runs. We give you a written price before any work starts, line by line, so parts, labor, and materials are separate and visible. Every completed job carries the 365-Day Done Right Promise: if the work fails within that full year, we come back and correct it at no charge.
DIY or Call Us?
Some of this is safe to check yourself. You can tighten an exposed hinge screw, clean a glide track, and confirm the model label without risk. Where it goes wrong is the redrill and remount: a door rehung on a hinge set at the wrong bore depth will sit crooked, pull the screws out of the frame again, and mark the door face. If a hinge screw has stripped its hole, the fix is a proper fill and remount, not a bigger screw. And if the work reaches into plumbing or electrical for an island or a sink change, that’s licensed work and not a homeowner job.
Most replacement parts for a Mr-Glass kitchen are ordered to the model spec rather than pulled from a shelf, so the right answer is to get the part matched and the install scheduled together. Call (844) 797-9259 for a free estimate. A live person answers, day or night.
FAQs

Plan on 8 to 12 years for soft-close hinges and drawer glides under normal daily use, and expect the shorter end in a kitchen that faces west or runs hot. The cabinet boxes and doors themselves typically outlast the hardware by a wide margin, which is why component replacement usually makes more sense than a full cabinet swap. Call (844) 797-9259 for an exact quote on your kitchen; estimates are free.
Often yes, especially hinges. A loose hinge plate can be re-tightened and readjusted, and a stripped screw hole can be filled and remounted properly. A failed soft-close damper or a flat-spotted glide can’t be rebuilt, so those get replaced. We’ll tell you which one you’re looking at before any work starts, with the price in writing. Call (844) 797-9259 to schedule a free estimate.
A hardware-only job, like replacing hinges and glides across a standard kitchen, is usually a single-day visit once the correct parts are on site. A component swap that includes a door front or a drawer box takes a bit longer. A full cabinet or countertop change runs multiple days. We confirm the schedule in writing along with the price. Call (844) 797-9259 for a free estimate.
We identify the model from the cabinet label and match the hinge bore spacing and glide series to the spec, then order the OEM part or a verified aftermarket equivalent that fits. We don’t claim to stock Mr-Glass parts, and nothing gets carried on a truck; the part is ordered to your kitchen. If you’re weighing a Mr-Glass refresh against other lines, we also install KraftMaid, Cambria, and Silestone. Call (844) 797-9259 to start with a free estimate.
Written by the team at Bradford Remodeling Boulder City, serving Boulder City and nearby areas.












