







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Schluter Home Additions & ADU: The Boulder City Owner’s Guide
We install Schluter-compatible home additions and ADUs in Boulder City, and a typical build runs $45,000 – $130,000 depending on footprint, site work, and finish level. ADU construction is the higher end of that, $90,000 – $220,000, and garage conversions land between $30,000 and $80,000. This page is for the homeowner who already knows the waterproofing and uncoupling side of the assembly matters and wants straight answers on which Schluter components fit, what fails first, and what the fix costs. Most Boulder City owners find the problem the same way: a tile floor in the new room that sounds hollow, a grout line that keeps reopening, or a shower curb that wicks moisture long after the finish went in.
Key takeaways
- Schluter builds several distinct systems, and the right part depends on which assembly your addition used.
- Boulder City’s desert swing – hot days, cold nights, and very low humidity – stresses a poorly installed membrane faster than most owners expect.
- We’re an independent service provider. We are not Schluter and we don’t speak for them.
Which Schluter Models This Applies To

Schluter isn’t one product; it’s a family of assemblies, and “the part” changes with each. The common ones in an addition or ADU are DITRA and DITRA-HEAT uncoupling membranes under tile, KERDI and KERDI-BAND for waterproofing shower and wet areas, KERDI-BOARD as a backer panel, and SCHIENE, DILEX, and TREP-E as edge and movement profiles. If your layout includes heated tile, you’re likely on a DITRA-HEAT system with a specific thermostat and cable spec.
To match the right part, read the imprint stamped on the membrane or profile, not the box the installer threw out. DITRA and DITRA-HEAT are printed along the roll with the series name and the square grid that sets the fleece side up. Roll width and grid count are your first I.D.; profiles have a shape code on the leg. That matters because OEM Schluter parts are dimensionally matched to the system, while a generic uncoupling mat or edge strip can be a millimeter off and still “fit” until it doesn’t. We order OEM when the assembly’s warranty depends on it and quality aftermarket only where the profile doesn’t control the waterproofing.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your Schluter Home Additions & ADU Is Failing
- Hollow tile and drifting grout. There’s no uncoupling layer doing its job, so seasonal movement in the slab or subfloor transfers straight into the tile. You’ll hear it first, then see hairline grout cracking at the room edges.
- Recurring moisture at a shower curb or niche. A KERDI band or corner that wasn’t overlapped to spec lets water behind the membrane. It shows up as darkened grout, a soft curb, or efflorescence long after the finish looked fine.
- Lifted or popped edge profiles. A SCHIENE or DILEX strip set without the correct thin-set bed pulls loose at the threshold. It’s the first piece to fail because it takes the traffic and the thermal swing at a doorway.
- Cold or dead zones in heated tile. A DITRA-HEAT cable that was nicked or a thermostat wired to the wrong sensor leaves half the floor unresponsive. It reads as a part failure, but the fault is usually at the splice or the sensor.
- Cracks tracing the floor grid. When joints open along the familiar grid lines, the substrate has moved and the membrane wasn’t controlling it. This is the classic sign the assembly was specified wrong for the addition’s foundation.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included

Straight numbers for Boulder City, installed. These cover materials plus labor, the membrane or profile, substrate prep, and re-setting the finish over the repair.
| Scope | Installed range |
|---|---|
| Full home addition | $45,000 – $130,000 |
| ADU construction | $90,000 – $220,000 |
| Garage conversion | $30,000 – $80,000 |
The range is driven by square footage, foundation type, whether plumbing and electrical rough-in move, and how much finished surface has to come up to reach the failed layer. We give a written price before any work starts, so the number you hear is the number you get. Every finished project carries the 365-Day Done Right Promise: if the work fails inside that year, we come back and correct it at no charge.
DIY or Call Us?
You can safely read the membrane imprint, photograph the failed area, and check the thermostat and breaker on a heated floor. That’s diagnosis, and it helps. Where it goes wrong is the repair itself. Waterproofing is a continuous-system job: one under-lapped KERDI band or one profile set without the right bed and the leak returns in a season, behind new tile that has to come back out. On a slab in Boulder City, the thermal movement that cracked the first install will crack a second if the uncoupling layer is skipped. Setting waterproofing and uncoupling correctly is trained work, and we’d rather you not pay twice. Call (844) 797-9259 and we’ll price the fix in writing.
FAQs

A correctly installed DITRA or KERDI assembly should hold for the life of the tile, roughly 25 years or more. Boulder City’s hot days and cold desert nights work the substrate hard, so the uncoupling layer and the band overlaps are what carry that lifespan. If the first install skipped either, expect failure in a few seasons rather than decades. Call (844) 797-9259 for a free look and estimate.
Often, yes. A small hollow spot or a single lifted profile can be cut back, re-membraned, and re-set without pulling the whole floor. Broad grout cracking or a wet shower curb usually means the assembly itself failed and needs more than a surface patch. We tell you which one you’re looking at before any price is written.
A localized membrane or profile repair is typically one to two days. A full wet-area rebuild runs several days because the waterproofing has to cure and pass before tile goes back down. We schedule the timeline in writing with the price. Call (844) 797-9259 to set it up.
We match the OEM Schluter component to the stamped series and spec on your assembly, then order it, rather than carrying parts on a truck or keeping stock. That guarantees the part is right for the system and its warranty. For surrounding finishes we also work with KraftMaid, Cambria, and Silestone, among other documented brands.
If your addition or ADU has a Schluter layer that’s failing, don’t guess at the fix or let a second bad install cost you the tile twice. Bradford Remodeling Boulder City gives you a written price before work begins, background-checked technicians on every job, and the 365-Day Done Right Promise on the finished work. Call (844) 797-9259 for a free estimate.
Written by the team at Bradford Remodeling Boulder City, serving Boulder City and nearby areas.












