







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Techo-Bloc Driveway & Pavers: The Boulder City Owner’s Guide
We install Techo-Bloc driveway and paver systems across Boulder City, and a full paver driveway typically runs $7,000 – $18,000 installed, while a paver patio lands between $3,500 and $11,000. Most owners don’t go looking for this page until something has already gone wrong: a paver has rocked underfoot after a monsoon season, a joint line has opened a half-inch wide, or a few units along the driveway apron have settled and now hold a puddle after every rain. Those are the three calls we get most in Boulder City, and each one points to a different failure underneath the surface. Techo-Bloc is a premium brand, so the block itself is rarely the problem. The base, the edge restraint, or the joint sand almost always is.
Key Takeaways
- Installed paver driveways in Boulder City run $7,000 – $18,000; patios run $3,500 – $11,000.
- Techo-Bloc units don’t usually fail. The base, edging, and polymeric joint sand do.
- We’re an independent contractor, not affiliated with Techo-Bloc, and every paver job carries our 365-Day Done Right Promise.
Which Techo-Bloc Models This Applies To

Techo-Bloc runs several paver families, and each one wants a different bedding and joint detail. The Blu 60mm and Blu 80mm lines are the standard driveway and patio workhorses, and they’re widely specified in Boulder City because the thicker profile handles vehicle loads better than thin-set patio block. The Villagio and Villagio 60 lines are the tumbled, old-world look you see on a lot of front walks and patios. And the Para and Industria series show up on driveways where the owner wanted a tighter, cleaner joint pattern.
Identifying your paver family matters because replacement units have to match thickness and joint tolerance. Techo-Bloc sizes are nominal, not always exact. A Blu 80 that measures a hair under 80mm won’t seat level against a batch that measures full, and a mismatched joint throws off the pattern across the whole field. The clean way to identify what you have is to pull one loose unit and measure both the thickness and the face dimensions with a caliper, then compare that against the spec sheet for the line. Order from the same production run when you can, because dye lots vary between batches, and a mismatched lot will read as a patch job from the sidewalk. On the OEM-versus-aftermarket question, this is one place we push for the genuine Techo-Bloc profile: the base prep and joint sand matter more than the block, but the block has to match the existing field, and the aftermarket lookalikes don’t.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your Techo-Bloc Driveway & Pavers Is Failing
Here’s how a failing paver system usually announces itself, and what’s actually happening underneath.
- Pavers rocking or wobbling underfoot. The bedding sand has washed out or compacted unevenly, so there’s a void under the unit. A wobble you can feel through the sole of a shoe is the first real warning sign, and it should be addressed before it spreads.
- Widening joint lines and migrating sand. Polymeric joint sand has broken down, often from UV and the fast wet-dry cycling that Boulder City sees. Once joints open, water goes straight into the base, and the problem compounds with every rain.
- Settlement and ponding after rain. The base layer wasn’t compacted deeply enough or the drainage slope was lost. Water sitting in a low spot after a storm is a base failure, not a surface problem.
- Edge units pushing out or heaving. The edge restraint has failed or wasn’t pinned deeply enough, so the perimeter creeps outward and the field opens up. Driveway aprons and the ends of a paver run fail first.
- Chipping, spalling, or efflorescence that won’t wash off. Surface damage from vehicle load, road salt, or the mineral bleed that intense desert sun pulls out of concrete block. Efflorescence can be cleaned, but recurring white haze usually means moisture is trapped below.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included

Here’s what paver work and the surrounding driveway scope costs in Boulder City. Every price we quote is a written price before any work starts, and there are no numbers that move at the door.
- Paver driveway installation: $7,000 – $18,000
- Paver patio installation: $3,500 – $11,000
- Concrete driveway installation: $4,500 – $12,000
- Asphalt driveway paving: $3,500 – $9,000
- Driveway replacement: $5,000 – $14,000
- Driveway sealing: $250 – $700
What drives the range: total square footage, how much of the base has to be excavated and rebuilt versus reused, whether the edge restraint needs replacing, and how many units have to match an existing dye lot. Parts and labor are itemized separately on the written quote, so you see the block cost and the base and labor cost as separate lines. Every completed paver job carries our 365-Day Done Right Promise: if the work fails within the guarantee period, we come back and correct it at no charge.
DIY or Call Us?
An owner can safely do a few things. Pull up one loose paver and measure it. Sweep fresh joint sand into open lines. Hose off efflorescence to see whether it returns. What we don’t recommend is pulling a full field of pavers to re-level a base yourself. The base is the whole job. Getting the depth, compaction, and drainage slope right is where DIY paver work fails, and it fails in exactly the spot you’ll notice first: the low end of the driveway. If a paver has settled, there’s usually a much bigger base issue underneath the unit a neighbor’s tree or a bad downspout didn’t help. That’s a job for a crew that does the substrate by the book. Call (844) 797-9259 to schedule a free estimate.
FAQs

Techo-Bloc pavers themselves will last decades, but the system underneath is what determines real lifespan. In Boulder City, the base, edge restraint, and polymeric joint sand take a hard hit from intense sun and fast wet-dry cycles, so the base and joints are usually what need attention well before the block wears out. A properly installed driveway with a deep compacted base should hold for 20-plus years. Call (844) 797-9259 if yours is wobbling or ponding; an estimate is free.
Yes, in most cases it can. If only a section of pavers has settled or the joint sand has failed, we can lift the affected area, rebuild the base, reset the units from the same dye lot, and re-joint the whole field. Full replacement is usually only necessary when the base has failed across the whole driveway or the edge restraint is gone end to end. We tell you which one it is, in writing, before any work starts.
A localized repair and re-joint typically runs one to three days, while a full paver driveway replacement runs several days to a couple of weeks depending on square footage and how much base has to be rebuilt. We schedule one job at a time, and we don’t promise same-day turnarounds on planned paver work.
We match the paver family, thickness, and dye lot before we lift a single unit. We work from a documented roster of premium hardscape brands, so the block spec and manufacturer warranty are traceable. We don’t carry parts on a truck and don’t claim to. We measure, identify, and order the right unit so your repair reads as a seamless field, not a patch. Our technicians have up to 22 years of experience. We also install KraftMaid, Cambria, and Silestone products, and we’re an independent contractor, not affiliated with Techo-Bloc. Call (844) 797-9259 for a free estimate.
Written by the team at Bradford Remodeling Boulder City, serving Boulder City and nearby areas.












