







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Tremron Bathroom Remodeling: The Boulder City Owner’s Guide
Tremron bathroom remodeling in Boulder City runs $9,000 to $28,000 installed, depending on whether you’re reworking a shower surround, a full wet wall, or the whole room. Small bathrooms land lower, in the $5,000 to $12,000 range. We’re an independent remodeling contractor, not affiliated with Tremron, and we work with Tremron porcelain pavers and tile as part of The Garrison Standard’s documented-material roster. Every price we give you is written before any work starts, and every finished bathroom carries our 365-Day Done Right Promise.
Owners in Boulder City usually find this part when a bathroom paver or floor tile starts looking wrong rather than sounding wrong. You’ll notice a hollow knock underfoot, a hairline crack spreading across a glazed surface, or a grout line that keeps shedding sand despite repeated resealing. By the time you call, most people have already resealed twice and are ready for someone to tell them the truth about why it keeps failing.
Key Takeaways
- Full Tremron bathroom remodeling in Boulder City: $9,000 to $28,000 installed.
- Small bathroom projects: $5,000 to $12,000.
- We operate independently of Tremron and work from written specifications, not guesswork.
- Written price before work starts, live phone coverage 24/7, and the 365-Day Done Right Promise on every completed project.
Which Tremron Models This Applies To

Tremron produces porcelain pavers and tile, plus a few concrete paver lines, and the model matters because the same nominal “12×12” can differ by a millimeter or two across series. That gap is enough to break a grout joint on a shower pan or leave a lippage edge you’ll feel barefoot every morning. If your tile came from a Tremron colorway that’s been discontinued, matching a replacement tile to the original is often harder than replacing the whole field.
Here’s how to identify what you actually have:
- Check the original cartons. Tremron prints the series name, colorway, and nominal size on every box. If you kept one spare carton in the garage – most Boulder City owners have one tucked away – that’s your answer.
- Measure a full tile, not a grout line. A “24×24″ porcelain paver might measure 23-5/8″ actual with a 3/16” joint. Pull out a tape measure and confirm before ordering.
- Check the warranty card. Tremron porcelain lines carry manufacturer warranties that vary by series; the paperwork tells you which one you’re under.
- Photograph the back of a loose tile. The back stamp, if visible, tells us the series without breaking anything out.
On the OEM-versus-aftermarket question, Tremron’s own tile is the safest match for an original install since it carries the manufacturer warranty. But when a colorway is discontinued, a quality porcelain equivalent from a documented brand – or a complementary Cambria or Silestone surface if you’re reworking the vanity area – is a defensible substitute, provided the thickness and coefficient of friction match the original specification.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your Tremron Bathroom Remodeling Is Failing
Each of these points to a specific failure mode rather than general wear. If you catch the cause early, you can often save the tile.
- Hollow tapping sound underfoot. The tile has debonded from the substrate, usually because the thinset didn’t fully cure or the substrate shifted. A single loose tile is fixable; a field of them points to a substrate problem that has to be addressed at the bed.
- Hairline cracks spreading across the face. Cracks over a joint or corner typically mean the substrate is flexing under the tile – common in a Boulder City bathroom where summer slab movement and winter temperature swings cycle the floor.
- Grout that keeps shedding despite resealing. Sanding grout out and reapplying it hides the symptom; if you’ve done it more than twice, the joint is moving and the substrate behind it is the real culprit.
- Dark staining or a musty smell at the shower pan edges. Water is getting behind the tile through a failed joint or a compromised waterproofing membrane. This one is worth attention before it reaches the wall framing.
- Lippage you can feel barefoot but barely see. Lipping usually means the substrate isn’t flat within the tolerance required by the tile’s size. Larger porcelain pavers need a flatter substrate than small mosaic tile, which is why this shows up more on Tremron’s large-format lines.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included

Boulder City Tremron bathroom remodeling ranges from $9,000 to $28,000 installed. The written price we hand you before work starts breaks down materials, labor, and substrate prep as separate line items, so you can see exactly where the range lands and why.
What drives the number:
- Room size and tile layout. A 5×8 powder room is a different job than a full master with a walk-in shower and floor tile. Small bathroom remodels come in at $5,000 to $12,000.
- Substrate condition. A flat, sound substrate keeps the number at the bottom of the range. Rotted subfloor, cracked slab, or a failed waterproofing membrane pushes it up.
- Fixture scope. Tile work alone versus tile plus a walk-in shower conversion, vanity install, or tub-to-shower conversion. A walk-in shower install runs $4,500 to $12,000; a vanity install is $800 to $3,000.
- Tile removal and disposal. Old tile has to come out, and old thinset has to come off the substrate before new goes down.
Every finished project is covered by our 365-Day Done Right Promise: if the work fails inside the first year, we come back and correct it at no charge. No exceptions, no fine print.
DIY or Call Us?
You can safely check whether tile is debonded by tapping with a screwdriver handle and listening for hollow spots. You can confirm the tile size with a tape measure and photograph the back stamp. You can pull your original carton out of the garage. That’s the honest scope of what an owner can do without breaking into the substrate.
Where DIY goes wrong: substrate prep. The hard part of a tile installation isn’t laying tile, it’s making sure the substrate is flat, sound, and correctly waterproofed in the wet zone. A DIY install on an imperfect substrate will look fine for six months and then start cracking, and by then you’ve paid twice. That’s the specific failure we get called to clean up most often in Boulder City.
The other thing that goes wrong is matching the tile when a colorway is discontinued mid-project. We source through a documented roster of name-brand materials, so we can tell you ahead of time whether a replacement Tremron line is available or whether an approved equivalent from Cambria, Silestone, or another documented brand is the honest answer. Call (844) 797-9259 to schedule a free estimate – estimates are free, no obligation.
FAQs

A properly installed Tremron tile floor will last 20 to 30 years in a Boulder City bathroom if the substrate and waterproofing were done right. The tile itself almost never fails on its own – the failure is almost always at the substrate, the thinset bond, or the grout joint. In our dry desert climate, exterior-facing bathrooms also see sun-driven heat expansion on south and west walls, which stresses grout joints faster than the interior of the room. If you’re seeing repeated cracking in the same spot, that’s the climate talking, not the tile.
Yes, sometimes. A single cracked or loose tile can often be pulled and replaced without touching the field if the colorway is still available and the surrounding bond is sound. A field of failing tiles, or repeated grout failure at the same joints, usually means the substrate needs to come up rather than the tile. A walk-through tells us which situation you’re in – and the free estimate tells you the honest answer before you spend a dollar. Call (844) 797-9259 to schedule.
Most full bathroom remodels in Boulder City run two to four weeks once work begins, depending on size and whether the substrate needs rework. A smaller fix – replacing a single tile or a failed grout joint – can be done in a day or less if the replacement tile is on hand. Substrate work and shower waterproofing add time and are worth every day. We don’t quote a timeline we can’t hold to; the written scope sets the schedule and the price together.
We work through a documented roster of name-brand materials with manufacturer specifications and warranties, so the tile and substrate materials are traceable before they’re ordered. That’s part of The Garrison Standard – nothing is ordered on a handshake. If your original Tremron colorway has been discontinued, we’ll tell you up front and present documented alternatives rather than a vague “we’ll figure it out.” Call (844) 797-9259 and we’ll start with the free estimate.
Sometimes we can match, sometimes the colorway is gone and the honest answer is a partial redo. Large-format porcelain is the harder case – the same nominal size varies by a millimeter or two across Tremron series, and an unmatched tile will show at the grout joint. If you have a spare carton, that’s the fastest way to match. If not, a documented substitute is the next option. We’ll tell you which you’re looking at during the free estimate.
Ready for a written price on your Tremron bathroom project in Boulder City? Call Bradford Remodeling Boulder City at (844) 797-9259 to schedule your free estimate. We answer 24/7 with a live person, and every price we hand you is written before any work starts. Our technicians have up to 22 years of experience, and our crews are background-checked and uniformed on every job. We also work with KraftMaid, Cambria, and Silestone on adjacent bathroom and kitchen projects. The 365-Day Done Right Promise carries every finished bathroom we hand back to you.
Written by the team at Bradford Remodeling Boulder City, serving Boulder City and nearby areas.












